Preparations
Setting Up the Remote Control
In addition to controlling the receiver, the supplied remote control can operate your other components (DVD, MD, VCR, TV, LD, CD, etc.). If your component(s) are listed in the “Preset Code List”, simply recall the corresponding preset code.
Recalling preset codes (VSX-D509S)
The following steps show you how to recall preset codes for each MULTI CONTROL button. Once the preset code is assigned, pressing the button will automatically set the remote to operate the respective component.
•Refer to “Preset Code List” on pages 53 to 56 for the components and manufacturers
memo available.
• Refer to “Controlling the Rest of Your System” on pages 46 to 50 for detailed explanations on how to operate your other components.
Set up
SOURCE | RECEIVER |
| ||
DVD | TV |
| VCR | |
| MULTI CONTROL |
| ||
RCV | CD |
| TUN | TVC |
1 |
| 2 |
| 3 |
MIDNIGHT |
| 5.1CH |
| ATT |
4 |
| 5 |
| 6 |
SIGNAL SELECT |
| EFFECT |
| |
7 |
| 8 |
| 9 |
+10 |
|
|
| DISC |
|
| 0 |
| ENTER |
TV CONTROL |
|
|
LED
2
3
1Press SETUP and hold for three seconds to
select the preset mode.
The LED will blink twice.
( To cancel the preset mode ) Press SETUP.
2Press the MULTI CONTROL button for the component you want to control.
TV | Each button can be set to control one of the following components |
TV VOL | TVFUNC MASTERVOLUME |
| DVD | : DVD/LD player or DVD Recorder | ||
|
|
|
|
| ||
| MENU |
|
|
| : TV , Satellite tuner or Cable TV tuner | |
| CHANNEL |
|
| TV | ||
| FQ |
|
| CD | : CD player, | |
|
|
|
|
| ||
ST |
| ST |
|
| : CD player, | |
| ENTER |
|
| |||
|
|
|
|
| ||
8 | FQ |
|
|
| : VCR or Digital Video Recorder | |
|
|
| VCR | |||
D.ACCESS | BAND | CLASS |
|
| : TV , Satellite tuner or Cable TV tuner | |
3 | 1 | Á |
| TVC | ||
MPX | DTV ON / OFF | DTV MENU |
|
|
| |
7 | 4 | ¢ |
| TUN | : FM/ AM tuner | |
2 | DSP TEST TONE |
|
|
| ||
CH SELECT | CH LEVEL | FL DIMMER |
| 3 Use the number buttons to enter the 4 digit | ||
LOUDNESS FUNCTION MUTING SETUP | 1,4 | |||||
setup code. | ||||||
|
| ë | ||||
|
|
|
| The LED will blink after each digit is input and will blink twice to | ||
|
|
|
| confirm a valid code has been input. | ||
REMOTE CONTROL UNIT |
| If the LED shows one long blink it means an invalid code has been | ||||
AV |
|
|
|
input. Check the preset code list and try again. If you are not able to input a preset code you can refer to page 26 to teach the remote control individual commands.
Repeat steps 1 through 3 to assign preset codes for as many components as necessary.
4Press SETUP to exit the preset mode.
The remote control returns to the previous operation mode. It will also return to the previous mode after ten seconds of inactivify.
• The RCV (Receiver) button cannot be preset.
memo • You can only input a code for the component type written on each MULTI CONTROL button. See page 29 for information on how to program a different type of component than specified on the button.
•If you recall a preset code for the tuner (TUN MULTI
COTROL), you will not be able to control the
of this receiver using the remote. To reset the remote to 23 the