Manuals / Polycom / Computer Equipment / Network Router

Polycom 7000, 6000 manual Bridge Statistics Report, Dlci Statistics Report

Models: 7000 6000

1 323

Download 323 pages 54.38 Kb

Page 237

IAD Reports

218

Bridge Statistics Report

To display the Bridge Statistics report, type B on the Interface Statistics menu. This report provides details about all packets sent and received on the IAD bridge.

Table 12–10.Bridge Statistics Report

Parameter

Description

Received Packet Information

bridge packets received

bridge octects received

discarded for lack of resources

bridge packets received and discarded

bridge packets sent to one other port

bridge packets sent to all other ports

Sent Packet Information

Total of bridge packet received from interface.

Total bridge octets/bytes received from interface.

Discarded received packets due to lack of resources: kernel memory or packet buffers.

Discarded received packets due to lack of packet buffers or Spanning Tree packets arrived on an interface, when Spanning Tree is not enabled.

No. of bridge packets sent to a proper low-level output port.

No. of bridge packets sent to all other bridge ports.

bridge packets sent

bridge octects sent

discarded for lack of resources

Total bridge packets sent.

Total octets/bytes of bridge packets sent.

Discarded transmitted packets due to lack of resources (kernel memory, packet buffers, etc.)

Packets Received by Type

spanning tree config packets received

spanning tree topology change packets received

spanning tree invalid packets received

spanning tree config packets sent

spanning tree topology change packets sent

No. of Spanning Tree Configuration packets received.

No. of Spanning Tree Topology Change packets received.

No. of invalid Spanning Tree packets, such as Wrong LSAP, Control, Protocol ID, Version, Length, and Message Type value.

No. of Spanning Tree Configuration packets sent.

No. of Spanning Tree Topology Change packets sent.

DLCI Statistics Report

To display the DLCI Statistics (Data Link Connection Identifier) report, Type D on the Interface Statistics menu.

This option is only displayed when Frame Relay is selected as the data link protocol.

NetEngine IAD User Guide

Image 237

Polycom 7000, 6000 manual Dlci Statistics Report, Bridge Statistics Report Parameter Description

Contents

Verilink Corporation User Guide VersionPage Table of Contents Chapter WAN Configuration Chapter AdministrationRouter Configuration Voice Path Configuration Bridge ConfigurationDhcp Server Configuration Firewall ConfigurationNAT Configuration Multicast ConfigurationIAD Reports Command Line InterfaceNetEngine IAD User Guide Appendix C NetEngine IAD Specifications Chapter Troubleshooting and DiagnosticsAppendix D Connector Pinouts Chapter VerificationPreface Audience ContentsPreface Xiv Conventions Product Warranty Contacting Verilink Repair InformationFCC Notice Regulatory NoticesIndustry Canada Notice FICUnderwriters Laboratories Statement CE MarkDeclaration of Conformity Xix Preface NetEngine IAD User Guide Family IAD IntroductionData Interfaces NetEngine 6000 IAD Family FeaturesDescription Front Panel Power and Status IndicatorsRear Panel Connectors NetEngine 7000 IAD Family Front Panel LEDs Family IAD Front PanelUniversal Serial Interface USI Port AC PowerIntroduction NetEngine IAD User Guide Quick Start Guide AC Power and Uninterruptible Power Supply Installing the IADUnpacking the IAD IAD Package ComponentsWiring Requirements Connect via Terminal EmulatorConnect the IAD to a PC Log in via a Terminal Emulation Program Power Up the IADMain Menu Setting the Ethernet Port IP AddressEnter connection to configure Available Interfaces G2237 xDSL G7070 Adsl ATU-R T1/E110/100BaseT Ethernet Abort Resetting the IAD Press R to Reset nowSelect priority Normal/High N/H N Running Telnet Connecting via TelnetUsing Menu Interface Configure Multicast Main Menu Reports Menu Configure LoginToggle Cmcp Debugging Manage Mgcp Embedded Client Selection Using Default or Current Values Entering Settings and ValuesNavigating the IAD Menu Interface Enter a new subnet mask for this interface 255.255.255.0USI Telephones Basic IAD Configur- ation ConnectingEthernet LAN Connection WAN ConnectionsTelephone Connections USI Connection 7200Reset the IAD Confirming Proper SetupVerify Normal Power Up and Operation Making RJ21X Connections 7000 familyAdministration IAD Security Security Level Privileges Security levelPrivileges Default User IDs and Passwords Security Level Changing a PasswordIncluding User ID and Passwords in Config Files Changing the User Level User IDEnter new User ID up to 17 characters Server Settings Changing the Radius Server AddressChanging the Radius Encryption Secret Displaying the Radius Configuration Using the Snmp Configuration Menu Setting UpEnabling and Disabling Snmp via IP Configuring the System ContactEnabling and Disabling Snmp via EOC Enabling Snmp via IP and EOCConfiguring the System Location Configuring the System NameConfiguring the System Community Configuring the Snmp Trap Host IP AddressConfiguring Restart Trap Maximum Delay Snmp traps sent via EOC are currently DisabledEnabling or Disabling Snmp Traps via EOC Upgrading the System Using Tftp Servers via LAN or WANCopying the Source Files Upgrading via TftpDownload using Tftp Enter ip address of Tftp server Verifying the UpgradeSetting up Your LAN Connection Establishing LAN Speed and Duplex ModeSelecting the Connection Pinging Network Devices Using System UtilitiesSetting up the USI Port Using Trace RouteConfiguring the Console Baud Rate Trace Route Results to 5msConfiguring the Console Timeout Period Managing Configuration FilesPerforming a Hard Reset Setting System DefaultsClearing the Last Reset Reason Saving System SettingsSelect Default Custom Defaults Factory Defaults Displaying the Event LogAdministration Displaying the IAD File Directory Using the File SystemRenaming Files Copying FilesDeleting Files Formatting the File SystemSetting the Ethernet MAC Address Using Debug MenuEnabling and Disabling PPP Debug Mode PPP Debug Mode is currently DisabledEnabling and Disabling Dhcp Client Debug Mode Enabling and Disabling STP Debug ModeDisplaying Error Dumps STP Debug Mode is currently DisabledLoading a Boot ROM File Performing File TransfersFile Transfer Method Receive via Tftp Receive via Xmodem Updating Acos Using File Transfer UtilitiesUpdating the System Are you sure? Y or N12. Tftp Server Menu Using the Tftp Server MenuDerived Timing Feature is currently DISABLED. Enable now? Y Setting Derived Timing OptionsEnabling and Disabling Derived Timing Enabling and Disabling Derived Timing Debug MessagesVerifying An IP Address Verifying an IP Address for Windows SystemsVerifying the IAD IP Addresses Administration NetEngine IAD User Guide WAN Configuration XDSL WAN Configuration Flowchart Basic WAN Setup TasksT1/E1 WAN Configuration Flowchart Identifying your WAN Interface and Datalink Protocol Channelized T1 with ATM Channelized T1 with Frame RelaySdsl with Frame Relay Sdsl with ATMUsing WAN Config- uration Menu Selecting the Datalink Protocol6100 or 6500 series IADs do not support Frame Relay Selecting ATM or Frame Relay WAN Configuration Menu ATMUndefined Mode Linked to Pots port Current configuration table is ChConfigurationUndefined Mode Linked Frame RelayEnter starting channel of this voice channel chunk Selecting the xDSL Interface Type Physical Interface10. G2237 xDSL Configuration Menu Configur- ing Shdsl InterfaceEnabling and Disabling Adaptive Rate Mode Selecting CPE or CO ModeSelecting the Line Rate Enabling and Disabling xDSL Debug MessagesConfigur- ing Sdsl Interface This section is only for configuring the Sdsl WAN interfaceOn the 6504, 6504i 15. Configure Sdsl Rate Mode Menu Configuring the Adaptive Rate Mode16. Sdsl Configuration Menu Setting Auto Sense-Coppermountain Dslam Setting Auto Cycle-Nokia DslamSetting Sync Delay-Lucent Dslam Setting AccessLan CPE Mode-AccessLan DslamSetting Sdsl Speed Manually Setting Sdsl Speed for Imas DSLAM-Nortel DslamSetting Sdsl Interface Mode Configuring the Sdsl Auto Cycle Speed TableEnter Sdsl Auto Cycle Speed Entry to Configure Using the Debug MenuDMT Alcatel Multi-Mode ADI Configur- ing Adsl Interface21. WAN Configuration Menu for T1/E1 Setting the Interface to T1 or E1Switching from E1 to T1 Switching from T1 to E1T1/E1 mode is currently T1 Change T1/E1 mode to E1? Y = yes T1/E1 mode is currently E1 Change T1/E1 mode to T1? Y = yesSelecting Frame Mode Configur- ing the T1 InterfaceSetting Line Build Out Configuring LoopbackSelecting B8ZS or AMI Enabling or Disabling All Channels Configuring the Transmit and Receive ChannelsConfiguring Transmit Clock Source Select Channel to Enable/Disable, then press EnterEnabling or Disabling Specific Channels Selecting a Channel RangeConfigur- ing the E1 Interface Displaying Physical Layer Stats and Alarm LogSelecting Frame/CRC4 Mode Select E1 Frame Mode Configuring S-Bits33. Configure S-Bits Menu 35. Select Tx Clock Source menu Configuring the Transmit Clock SourceRalos Rlos Rlof Sigfrz ATM PVCs ConfiguringAdding a PVC Enter Virtual Port Identifier VPICBR UBR 37. ATM Encapsulation Configuration MenuAAL2 LES, NBT Modifying a PVCSetting up AAL5 or AAL0 Encapsulation Setting up Proprietary Voice EncapsulationSetting up RFC 1483 VC Muxing or RFC 1483 LLC Encapsulation 43. ATM Encapsulation Configuration Menu 45. Ipcp Configuration Menu 47. ATM PCR Configuration Menu Setting up AAL1/CES51. AAL2 Audio Profile Format Menu Setting up AAL2/LESShowing Current PVCs Deleting a PVCConfiguring the F4 OAM VPI Configuring Payload ScramblingConfiguring the F4 OAM Type Displaying F4 OAM ConfigurationSending OAM Loopback Configuring EmptyCells Modifying a Dlci Frame Relay DLCIsConfiguring Transmit CIR Adding a DlciEnter the committed burst size Bc in number of bits Configuring FRF.12 Fragmentation Configuring Receive CIREnter the Circuit Throughput in bits/second Enter the excess burst size Be in number of bitsDisplaying Current DLCIs Deleting a DlciEnter maximum fragment size in bytes 100-1600 Port Dlci Encapsulation RAW No Encapsulation Select PortSetting FRF.12 Configuration Frame Relay OptionsSelecting Fragmentation Types CopperMountain Fragmentation Configuration Setting the Fragment Size ManuallyEnabling or Disabling FRF.12 Enabling Automatic Fragment SizingConfiguring the Maintenance Protocol Setting Real Time DlciEnabling or Disabling Coppermountain Fragmentation 64. Frame Relay Maintenance Protocol Menu Configuring the Congestion ParametersCmcp is currently Disabled Enter E to Enable, D to Disable Enabling or Disabling Coppermountain CmcpToggling Cmcp Debugging Quick Con- figuration 66. WAN Configuration MenuRouter Configuration Router Configuration Task Flowchart Basic Router Setup TasksRouter Configur- ation Menu Port IP Address Save new IP Information? -Y Unconfig- uring a Port IP Address Setting the Port Maximum Transmis- sion Unit Enabling and Disabling RIP is currently Disabled Enter E to Enable, D to DisableEnabling and Disabling RIP Poisoned Reverse by Port Enabling RIP GloballySetting the RIP Version Adding a Static Route Managing Static Default RoutesAdding or Changing the Default Route Setting Default RouteRemoving the Default Route Removing a Static RouteSetting the DNS Server IP Address Config- uring DNS ClientSetting the DNS Server Timeout Enter DNS Server Timeout in seconds 5...20Displaying the DNS Cache and Statistics IP Address Timer Host NameConfig- uring Dhcp Client Config- uring Dhcp Relay Configuring the Dhcp Server IP AddressEnabling and Disabling Dhcp Relay Displaying Dhcp Relay Statistics Enter Telnet Server Port IP Filtering Configuration MenuInput Filters Disabled, enter 1 to enable, 0 to disable Choosing a Port for IP FilteringGlobally Enabling and Disabling Filters Toggling Between Input and Output Filters Output Filters Disabled, enter 1 to enable, 0 to disableDisplaying Filters Inserting, Appending and Editing FiltersCopying Filters for Editing Filter ParametersDescription Copying a Filter Displaying a Filter in the BufferFilter Details Parameter Editing a Filter in the Buffer Deleting a Filter from the BufferDeleting an IP Filter Showing IP Filtering Statistics Deleting All Filters of the Chosen TypeClearing IP Filtering Statistics Are you sure you want to delete all filters? y/nIP Header Compression for SDSL, Port 1 is currently Config- uring IP Header Compress- ion IphcRoute Table Parameters Config- uring LAN IP Broadcast Destination Displaying RouteRouter Configuration 128 NetEngine IAD User Guide Bridge Configuration Bridge Configuration Task Flowchart Basic Bridge Setup TasksBridge Configuration Menu Bridge Configur- ation MenuEnabling or Disabling Bridging Globally Enabling and Disabling BridgingEnabling or Disabling Bridging by Port Available Interfaces G2237 xDSL 10/100BaseT Ethernet AbortPort Dlci Encapsulation Proprietary Voice Dlci Enabling or Disabling STP Globally Setting Bridge Aging Timer Enabling and DisablingEnabling or Disabling STP by Port Enter Bridge Aging time in seconds 1..3600G2237 xDSL 10/100BaseT Ethernet Abort Spanning tree over T1/E1 Port 1, is currentlyEnter Bridge Priority 1..65535 Enter Priority for Slot 2, Port 1 Enter Bridge Hello Time1..10Enter Spanning Tree Max Age 6..40 Enter Path Cost for Slot 1, Port 1 1..65535 Enter Spanning Tree Forward Delay 4..30Enter Ethernet address to delete from bridge database Deleting a Bridge Forwarding Database EntryVoice Path Configuration Basic Voice Path Setup Tasks Voice Path Configur- ation Menu CopperCom Setting Voice GatewayJetstream MgcpEnter number of ms to delay Setting Jitter DelaySetting All Ports to Loop Start Displaying Jitter Delay Setting Start ModeSetting All Ports to Ground Start Displaying Start ModeSetting Control ModeConfiguring Start Mode on an Individual Port Set On Hook Transmis- sion Mode Setting Compander ModeDisplaying Idle High Voltage Settings Setting Idle Voltage ModeReset the IAD Enabling and DIsabling Idle High Voltage GloballyEnabling and DIsabling Echo Cancellation Globally Setting Debug Mode Configur- ing Echo Cancell- ationDisplaying Echo Cancellation Settings Enabling and DIsabling Echo Cancellation for all PortsSetting Loop Gain for All Ports Setting Loop GainEnter Transmit Loop Gain for all ports range -9dB/ 3dB -2dB Enter Receive Loop Gain for all ports range -9dB/ 3dB -4dBConfiguring Loop Gain Setting by Port Displaying Loop Gain Settings11. Country Mode Selection Menu Setting Country ModeConfiguring Mgcp Parameters Embedded ClientEnter the listening port of the Notified Entity Displaying Mgcp Statistics Debugging MgcpRemoving a Connection Configuring Admin State per port Port AdministrationSetting Admin State Globally Displaying the Current Admin StateConfiguring Default Packet Size Restarting an EndpointEnter packet size in ms Managing Copper Com Call Control CopperCom ConfigurationDisplaying CopperCom Statistics Clearing CopperCom StatisticsDisplaying CopperCom Configuration Setting Compression FormatSetting Framing Format CopperCom Debug Control JetStream Call Control Settings Displaying StatisticsPerforming a Ring Test Configuring Trace Settings Displaying the IAD StateSelecting Insufficient Bandwidth Sound 20. Ring Test Menu for JetStream Voice Gateway Resetting StatisticsConfiguring for AAL2/LES CAS Configur- ing AAL2Configuring the IAD for a Specific AAL2/LES Gateway AAL2/LES Call Control Configuration Debugging StatisticsSetting the CAS Refresh Rate Manual ConfigurationEnabling and Disabling Ports Enabling and Disabling Idle CAS RefreshingSetting ATM Pace Control Manually Setting the Combined Use TimerChanging the Maximum CPS-SDU Size Enabling and Disabling User State ControlSetting the Minimum Signaling Bit Rate Setting the Audio Bit Rate MarginDisplaying Audio/CAS/Alarm Statistics Debugging AAL2/LES Gateways Displaying AAL2/LES StatisticsConfiguring for AAL2/LES CCS-ELCP AAL2/LES CCS-ELCP Menu Configuration Debugging StatisticsConfiguring Variant/Interface Management Debugging for AAL2/LES CCS-ELCP Setting Debugging OptionsViewing AAL2/LES Statistics Debugging Set Debugging Options Display V5 FSM StatesAudio and Alarm Statistics Displaying AAL2 Channel StatisticsClearing AAL2 Channel Statistics Voice Path Configuration 168 NetEngine IAD User Guide Creating a Firewall via IP Filtering Firewall ConfigurationFirewall Configuration 170 NetEngine IAD User Guide Dhcp Server Configuration Basic Server Setup Tasks Dhcp Server Configur- ation MenuDebugging Messages UsingServer Enabling and Disabling Checking for Additional ServersCurrent NetBIOS Node Type h-node Configur- ing Dhcp Server ParametersCurrent Subnet Mask = 255.255.255.0 Enter new Subnet Mask Current Domain name = Enter new Domain NameDhcp Address Range Pool Configur- ing a Dhcp Client Entry Enter Client entry number to configure 1...10Host name is currently Enter new Host Name Dhcp Server Configuration 176 Dhcp Server Details Field Server DetailsServer Assigned and Un- assigned Addresses Server StatisticsDhcp Server Statistics Dhcp Server Assigned Addresses Field DescriptionDeleting a Entry DetailsClient Entry Deleting a Assign- ment EntryDhcp Server Configuration 180 NetEngine IAD User Guide Multicast Configuration Multicast Configuration Menu Multicast Routing Source Menu Adding a Multicast Routing Source Enter IP address for the SourceEnter subnet mask for the source Network Address Netmask Incoming Interface 0.0 0.0.0.0 0.0.0.0 190.232.5.1 defaultIgmp Querier Interface 10/100BaseT Ethernet This interface Displaying PIM Neighbor Multicast Routing Table FieldsPIM Neighbor Interface 10/100BaseT Ethernet Multicast Configuration 188 NetEngine IAD User Guide NAT Configuration NAT NAT Default Parameter Settings RangeEnabling Translation1483LLC Encapsulation NAT Local Server Enter NAT Local Server Entry to ConfigureEnter NAT Local Server Translated Port Number 1..65535 Enter NAT Local Server Standard Port Number 1..65535NAT Timeouts NAT Port Range Enter Low End of NAT Port Range 5000..65534Enter High End of NAT Port Range 50000..65534 NAT Alias Entry Enter NAT Alias Entry to Configure 1..7NAT Statistics Report Entry NAT StatisticsConnection Details ConnectionNAT Connection Table Report Entry Enter outside port number of connectionNAT Connection Details Report Entry Deleting IP Addresses from NAT Tables NAT Alias TableNAT Local Server Table Report Report Entry NAT Alias Table Report Entry DescriptionEnter NAT Local Server Entry to Delete 1..20 Deleting a NAT Local Server Entry NAT AliasIAD Reports Reports Menu Report MenuCurrent Configuration Report Parameter Current Configur- ation ReportPort # IP Interfaces on Port # Current Configuration Report Parameter DescriptionNetwork Statistics Reports Icmp Statistics ReportIcmp Statistics Report Parameter Description Sent Packet Information Icmp Statistics Report ParameterIgmp Statistics Report Parameter Description Igmp Statistics ReportIP Statistics Report Igmp Statistics Report ParameterIP Statistics Report Parameter Description IP Statistics Report Parameter PIM Statistics Report Parameter Description PIM Statistics ReportTCP Statistics Report PIM Statistics Report ParameterTCP Statistics Report Parameter Description UDP Statistics Report TCP Statistics Report ParameterUDP Statistics Report Parameter Description UDP Statistics Report Parameter Clearing Network StatisticsAvailable Interfaces T1/E1 10/100BaseT Ethernet Abort Interface Statistics ReportsDisplay ARP Statistics Clear a StatisticARP Statistics Report Parameter Description ARP Statistics ReportInterface Statistics Report Parameter Description Interface Statistics ReportBridge Statistics Report Dlci Statistics Report10.Bridge Statistics Report Parameter Description Received Frame Information 11.DLCI Statistics ParameterATM PVC Statistics Report AAL1 Cpcs Statistics Report12.AAL1 Cpcs Statistics Report Parameter 13.Common CPCS-2 Statistics Report Parameter AAL2 Statistics ReportCumulative CPCS-2 Statistics Report Common AAL Statistics Report15.Common AAL Statistics Report Parameter IAD Reports 223 16.IP Header Compression Statistics Report Parameter IP Header Compression Statistics ReportPPP Statistics Report Clearing Interface Statistics17.PPP Statistics Report Parameter Description Media Statistics Menu Sample Media Statistics Reports18.Frame Relay Statistics Report Frame Relay Statistics Report19.Serial Statistics Report Parameter Serial USI Statistics Report20.ATM Statistics Report Field ATM Statistics ReportIAD Reports 230 21.G2237 xDSL Statistics Report Parameter G2237 xDSL Statistics ReportDSL2 22.Ethernet Statistics Report Parameter Description Ethernet Statistics Report22.Ethernet Statistics Report Parameter 23.G7070 Adsl Statistics Report Parameter G7070 Adsl Statistics Report24.POTS Statistics Report Parameter Pots Statistics ReportBRI Statistics Report Clearing Media Statistics25.BRI Statistics Report Parameter Bridge Forwarding Database Report ARP Table Report26.Route Table Report Parameter 27.ARP Table Report ParameterBridge Status Report No PPP Authorization Entries ConfiguredPPP Authorizati on Entries Report 28.Bridge Forwarding Database Report Parameter30.PPP Authorization Report Parameter System Uptime Report Memory Statistics ReportsSystem Memory Statistics Report Kernel Tasks Memory Statistics Report Zero All StatisticsIAD Reports 242 NetEngine IAD User Guide Command Line Syntax Command Line InterfaceCommand Example Intro- duction Set wan stp bridgeCommand Line Interface 244 Exit Ping Quit Rename file Command Line Interface ReferenceExit Ping IP address size triesReset system Remove lan ip address Set bridge globalSet bridge global on off Set bridge stp global Set dhcp server netbios Set dhcp server domainSet dhcp server range Set dns server address Set ip default route Set ip routeSet lan bridge on off slot interface port Set lan bridge Set lan ip addressSet lan rip Set lan stp bridge Set mgcp bracketing Set lan stp bridge on off slot interface portSet mgcp bracketing on off Set mgcp signaling connection port Set mgcp signaling tos byte valueSet mgcp listening port port Set nat Set mgcp voice connection Set mgcp voice tosSet mgcp voice connection slot interface port connection Set mgcp voice tos byte valueSet sdsl speed Set system defaults Set wan atm ppp auth Set system defaultsSet sdsl speed speed auto manual Set wan atm vc Set wan bridge Set wan atm vc vpi vci 1483 2364 slot interface portSet wan bridge on off slot interface port Set wan datalink framerelay atm slot interface port Set wan datalink Set wan framerelaySet wan ip address Set wan stp bridge Show ip routes Tftp receive Show configura- tion Show dhcp server configura- tionCommand Line Interface 258 NetEngine IAD User Guide Troubleshooting and Diagnostics Diagnostics Performing a Hotline Test Performing a Dialup TestPerform an all-lines test? Y or N Lines 1 and 2 are connected togetherPerforming a Phone Detect Test Performing a Power Supply TestRing all lines? YN or ESC Ring lines concurrently or sequentially? CS or ESCTroubleshooting and Diagnostics 263 Display hook state Press a key to exit 3 4 5 6 7 Performing an On/Off Hook TestSdsl BRI Diagnostics Menu Troubleshooting-Symptoms and Causes Trouble- shooting the IADProbable Cause Corrective Action Cannot receive or send data IAD Provisioning Parameters Troubleshooting and Diagnostics 270 NetEngine IAD User Guide Verification Testing the IAD Power-up Test Operational TestMainten- ance Displaying the Current Configur- ation Verification 274 NetEngine IAD User Guide ESC Menu MapMenu Map 276 Country Codes Belgium2 DenmarkItaly NetEngine IAD Specifications Table C-1 Family Analog Voice FeaturesFamily Table C-2 i and 6504i Isdn Voice Features Table C-4 Family Data Features Table C-3 Family Digital Voice FeaturesAdsl G.lite, G.dmt-6100-4 Table C-5 Family WAN Interface Features DescriptionAdsl Annex A, B-6104i SHDSL-TCPAM, SDSL-6504i, 6504Table C-5 Family WAN Interface Features T1 Interface-6200cT1 Provisioning-6200c Table C-6 Family Transport Protocol Features Description Table C-7 Family Configuration and Management FeaturesFrame Relay Table C-10 Network Interfaces Table C-8 Family Security FeaturesTable C-11 Family Voice Features AnalogDigital Table C-12 Family Data Features Table C-13 Family WAN FeaturesInterface Cell Delay Variation Buffer OAM Cell Handling Table D-1. RS-232 DB-9 Console Port Pin Assignments Signal Connector PinoutsTable D-5 BaseT Connector Pin Assignments RJ48 Signal Table D-4 BaseT Connector Pin Assignments SignalTable D-6. ADSL/SDSL Connector Pin Assignments RJ45 Signal Table D-7. G.SHDSL Port Pin Assignments RJ11 Line Tip RingPin Signal Table D-8. T1/E1 Connector Pin Assignments SignalTable D-9. USI Port for RS-530, V.35 and RS-449 Signal RS-530 RS-449Connector Pinouts 292 NetEngine IAD User Guide Glossary Glossary 294 Glossary 295 Glossary 296 Adsl IndexDNS Shdsl LAN NAT Safeguards WAN NetEngine IAD User Guide