ELECTRICAL
REQUIREMENTS AND SAFETY
POWER SUPPLY AND MOTOR SPECIFICATIONS
!WARNING
To avoid electrical hazards, fire hazards, or damage to the tool, use proper circuit protection. Use a seperate electrical circuit for your tool. Your saw is wired at the factory for 120 V operation. Connect to a 120 V, 15 Amp circuit and use a 15 Amp time delay fuse or circuit breaker. To avoid shock or fire, if power cord is worn, cut, or damaged in any way, have it replaced immediately.
GROUNDING INSTRUCTIONS
!WARNING
This tool must be grounded while in use to protect the operator from electrical shock.
IN THE EVENT OF A MALFUNCTION OR BREAKDOWN, grounding provides a path of least resistance for electric currents and reduces the risk of electric shock. This tool is equipped with an electrical cord that has an
DO NOT MODIFY THE PLUG PROVIDED. If it will not fit the receptacle, have the proper receptacle installed by a qualified electrician.
IMPROPER CONNECTION of the equipment grounding conductor can result in risk of electric shock. The conductor with the green insulation (with or without yellow stripes) is the equipment grounding conductor.
If repair or replacement of the electrical cord or plug is necessary, do not connect the equipment grounding conductor to a live terminal.
CHECK with a qualified electrician or service person if you do not completely understand the grounding instructions, or if you are not certain the tool is properly grounded.
USE only
Use a separate electrical circuit for your tool. This circuit must not be less than #14 wire and should be protected with a 15 Amp time lag fuse. Before connecting the motor to the power line, make sure the switch is in the off position and the electric current is rated the same as the current stamped on the motor nameplate. Running at a lower voltage will damage the motor.
GUIDELINES FOR EXTENSION CORDS
USE THE PROPER EXTENSION CORD. Make sure your extension cord is in good condition. Use an extension cord heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power, overheating
and burning out of the motor. The table below shows the correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord.
Make sure your extension cord is properly wired and in good condition. Always replace a damaged extension cord or have it repaired by a qualified technician before using it. Protect your extension cords from sharp objects, excessive heat and damp or wet areas.
MINIMUM GAUGE FOR EXTENSION CORDS (AWG)
Ampere Rating |
| Total length of Cord |
| ||||
|
|
|
|
|
|
|
|
More Than | Not More Than | 120V | 25 | 50 | 100 | 150 | ft. |
|
|
| (7.62 | 15.24 | 30.48 | 45.72 | m) |
|
| 240V | 50 | 100 | 200 | 300 | ft. |
|
|
| (15.24 30.48 60.96 91.44 m) | ||||
|
|
|
| ||||
|
|
| AWG - American Wire Gauge | ||||
|
|
|
|
|
|
|
|
0 | 6 |
| 18 | 16 | 16 | 14 |
|
|
|
|
|
|
|
|
|
6 | 10 |
| 18 | 16 | 14 | 12 |
|
|
|
|
|
|
|
|
|
10 | 12 |
| 16 | 16 | 14 | 12 |
|
|
|
|
|
|
| ||
12 | 16 |
| 14 | 12 | Not Recommended | ||
|
|
|
|
|
|
|
|
!WARNING
This tool is for indoor use only. Do not expose to rain or use in damp locations.
This tool is intended for use on a circuit that has a receptacle like the one illustrated in Fig. 1. Fig. 1 shows a
!CAUTION
In all cases, make certain the receptacle is properly grounded. If you are not sure, have a qualified electrician check the receptacle.
Fig. 1 | |
|
Grounding Prong
Properly Grounded
Fig. 2
Grounding Lug
Make sure this is connected to a known ground.
Adapter 
Receptacle
– 7 –
