41. Route the Weight Cable (110) over a 90mm | 41 | 75 |
|
|
Pulley (63) and down through the Right Top |
|
| ||
|
|
| ||
Frame (5). Attach the Pulley inside the Top Frame |
| 102 |
|
|
|
| 99 |
| |
with an M10 x 80mm Bolt (75), two M10 Washers |
| 99 |
| |
| 90 | |||
(99), two M10 x 19mm Spacers (102), and an |
| |||
|
| |||
|
|
|
| |
M10 Nylon Locknut (90). |
| 63 |
|
|
|
|
|
| |
|
| 110 |
|
|
|
| 5 |
|
|
42. Wrap the Weight Cable (110) under a 90mm | 42 |
| 110 |
|
Pulley (63). Attach the Pulley, a Cable Trap (68), | 64 |
| ||
|
|
| ||
and two Half Finger Guards (66) at the second |
|
|
|
|
hole from the top of the two Pulley Plates (51) |
|
|
| 63 |
with an M10 x 50mm Bolt (64) and an M10 Nylon |
|
|
| |
| 66 |
| 66 | |
Locknut (90). Make sure the Cable Trap and |
|
| 90 | |
|
|
| ||
Finger Guards are oriented as shown. |
|
| 68 |
|
|
|
|
| |
|
| 51 |
|
|
|
|
|
| 51 |
43. Wrap the Weight Cable (110) over a 90mm Pulley | 43 | Bracket |
|
|
(63). Attach the Pulley to the indicated bracket on |
|
| ||
| 5 |
|
| |
the Right Top Frame (5) with an M10 x 45mm |
|
|
| |
|
|
|
| |
Bolt (80) and an M10 Nylon Locknut (90). |
|
|
|
|
|
|
|
| 90 |
|
| 80 | 63 | 110 |
|
|
|
| |
44. Wrap the Weight Cable (110) over a 90mm Pulley | 44 | Attach pulley |
| Bracket |
(63). Attach the Pulley and a Cable Trap (68) to |
| |||
|
|
| ||
| on this side |
|
| |
the indicated bracket on the Right Top Frame (5) |
|
|
| |
|
|
|
| |
with an M10 x 45mm Bolt (80) and an M10 Nylon |
|
|
|
|
Locknut (90). Make sure the Cable Trap is ori- |
|
| 80 | 5 |
ented to hold the Cable in the groove of the |
|
| ||
| 63 |
|
| |
Pulley. |
|
|
| |
|
| 68 | 110 | |
|
| 90 |
|
|
45. Set the M12 Washer (33) on top of the Weight | 45 |
|
|
|
Tube (47). Thread the M12 Nut (49) all the way |
|
|
| |
| 110 |
| ||
onto the Weight Cable (110). |
|
| ||
|
|
|
| |
Thread the Weight Cable (110) into the Weight |
| 49 |
| |
| 33 |
| ||
Tube (47) a couple of turns. |
|
| ||
|
| 47 |
| |
|
|
|
| |
| 17 |
|
|
|
