Manuals / Q-Logic / Computer Equipment / Computer Hardware

Q-Logic QLA2300 manual QLogic Corporation First Printed July, 800 867-7274 or 949, Page

Models: QLA2300

1 30

Download 30 pages 40.11 Kb

Page 4

© 2000–2001 QLogic Corporation

QLogic Corporation

© 2000–2001 QLogic Corporation

First Printed: July 2000

All Rights Reserved Worldwide.

Printed in U.S.A.

QLogic Corporation, 26600 Laguna Hills Drive, Aliso Viejo, CA 92656

(800) 867-7274 or (949) 389-6000

Page iv

FC2251101-00 D

Image 4

Q-Logic QLA2300 manual QLogic Corporation First Printed July, All Rights Reserved Worldwide Printed in U.S.A, Page

Contents

Hardware Installation Guide for the QLA2300 Board Family Fibre Channel Host Adapter Boards for the PCI BusPart of the SANblade Family of Products FC2251101-00 D October 5QLogic is a trademark of QLogic Corporation Page QLogic CorporationFC2251101-00 D QLogic Corporation 2000-2001 QLogic Corporation First Printed JulyAll Rights Reserved Worldwide Printed in U.S.A QLogic Corporation, 26600 Laguna Hills Drive, Aliso Viejo, CATable of Contents Fast!UTILFIGURES TABLESPage PageWhat is Fibre Channel? IntroductionSection General DescriptionFeatures Hardware Installation Preinstallation ProceduresWhat You Need for Installation QLA23xx Board Components2 - Hardware Installation Figure 2-1. QLA2300/2310 Board LayoutFigure 2-2. QLA2300F/2310F Board Layout SERIAL NUMBER J1Figure 2-3. QLA2310FL Board Layout Figure 2-4. QLA2302F Board LayoutQLA23xx Board Components J2 J22 - Hardware Installation Figure 2-5. QLA2312F Board LayoutFigure 2-6. QLA2312FL Board Layout SERIAL NUMBER J1LEDs 2.3.1Figure 2-7. QLA2300/2300F/2310/2310F/2310FL Board LED Activity Figure 2-8. QLA2302F/2312F Board LED ActivityPower Distribution Installation in the ComputerJumpers 2.3.2PCI connectors vary among system board manufacturers. The QLA23xx board is a 64-bit PCI device that can function in a 32-bit PCI slot the slot conforms to the PCI specification the rear edge of the PCI slot is notched. If you try to install the QLA23xx board into a PCI slot that does not conform to the PCI specification, you may damage the QLA23xx board Installation Help Troubleshooting Problems After InstallationHardware Problem Checklist System Configuration Problem ChecklistFibre Channel Problem Checklist Configuration Settings Appendix AIntroduction Fast!UTILHost Adapter Settings Selectable Boot SettingsTable A-1. Host Adapter Settings A.2.1Restore Default Settings Advanced Adapter SettingsRaw NVRAM Data Table A-2. Advanced Adapter SettingsExecution Throttle. This setting specifies the maximum number of commands executing on any one port. When a port’s execution throttle is reached, no new commands are executed until the current command finishes executing. The valid options for this setting are 1-256. The default is Table A-3. Extended Firmware Settings Extended Firmware SettingsA.2.6 Table A-4. RIO Operation Modes Table A-5. Connection OptionsOperation Mode OptionFibre Disk Utility Scan Fibre Channel DevicesSelect Host Adapter A - Fast!UTIL Select Host AdapterFC2251101-00 D Specifications Appendix BTable B-2. QLA23xx Board Specifications Table B-1. QLA23xx Board Operating EnvironmentTable B-2. QLA23xx Board Specifications Continued QLA2300/QLA2310 HSSDC connector that supports copper cabling. FibreLabel Appendix CC - Label FC2251101-00 D