Manuals
/
Q-Logic
/
Computer Equipment
/
Computer Hardware
Q-Logic
manual Hardware Installation Guide for the QLA2300 Board Family
Models:
QLA2300
1
1
30
30
Download
30 pages
40.11 Kb
1
2
3
4
5
6
7
8
<
>
Troubleshooting
Specs
Install
Configuration Settings
Fibre Channel Problem Checklist
Execution Throttle. This setting specifies the maximum number of commands executing on any one port. When a port’s execution throttle is reached, no new commands are executed until the current command finishes executing. The valid options for this setting are 1-256. The default is
Restore Default Settings
Host Adapter Settings
What is
Power Distribution
Page 1
Image 1
Hardware Installation Guide for the
QLA2300 Board Family
Fibre Channel Host Adapter Boards for the PCI Bus
Part of the SANblade Family of Products
FC2251101-00
D October 5, 2001
Page 2
Page 1
Image 1
Page 2
Contents
Fibre Channel Host Adapter Boards for the PCI Bus
Hardware Installation Guide for the QLA2300 Board Family
Part of the SANblade Family of Products
FC2251101-00 D October 5
QLogic is a trademark of QLogic Corporation
Page
QLogic Corporation
FC2251101-00 D
2000-2001 QLogic Corporation First Printed July
QLogic Corporation
All Rights Reserved Worldwide Printed in U.S.A
QLogic Corporation, 26600 Laguna Hills Drive, Aliso Viejo, CA
Fast!UTIL
Table of Contents
TABLES
FIGURES
Page
Page
Introduction
What is Fibre Channel?
Section
General Description
Features
Preinstallation Procedures
Hardware Installation
What You Need for Installation
QLA23xx Board Components
Figure 2-1. QLA2300/2310 Board Layout
2 - Hardware Installation
Figure 2-2. QLA2300F/2310F Board Layout
SERIAL NUMBER J1
Figure 2-4. QLA2302F Board Layout
Figure 2-3. QLA2310FL Board Layout
QLA23xx Board Components
J2 J2
Figure 2-5. QLA2312F Board Layout
2 - Hardware Installation
Figure 2-6. QLA2312FL Board Layout
SERIAL NUMBER J1
2.3.1
LEDs
Figure 2-7. QLA2300/2300F/2310/2310F/2310FL Board LED Activity
Figure 2-8. QLA2302F/2312F Board LED Activity
Installation in the Computer
Power Distribution
Jumpers
2.3.2
PCI connectors vary among system board manufacturers. The QLA23xx board is a 64-bit PCI device that can function in a 32-bit PCI slot the slot conforms to the PCI specification the rear edge of the PCI slot is notched. If you try to install the QLA23xx board into a PCI slot that does not conform to the PCI specification, you may damage the QLA23xx board
Installation Help
Problems After Installation
Troubleshooting
Hardware Problem Checklist
System Configuration Problem Checklist
Fibre Channel Problem Checklist
Appendix A
Configuration Settings
Introduction
Fast!UTIL
Selectable Boot Settings
Host Adapter Settings
Table A-1. Host Adapter Settings
A.2.1
Advanced Adapter Settings
Restore Default Settings
Raw NVRAM Data
Table A-2. Advanced Adapter Settings
Execution Throttle. This setting specifies the maximum number of commands executing on any one port. When a port’s execution throttle is reached, no new commands are executed until the current command finishes executing. The valid options for this setting are 1-256. The default is
Table A-3. Extended Firmware Settings
Extended Firmware Settings
A.2.6
Table A-5. Connection Options
Table A-4. RIO Operation Modes
Operation Mode
Option
Fibre Disk Utility
Scan Fibre Channel Devices
Select Host Adapter
A - Fast!UTIL
Select Host Adapter
FC2251101-00 D
Appendix B
Specifications
Table B-2. QLA23xx Board Specifications
Table B-1. QLA23xx Board Operating Environment
QLA2300/QLA2310 HSSDC connector that supports copper cabling. Fibre
Table B-2. QLA23xx Board Specifications Continued
Appendix C
Label
FC2251101-00 D
C - Label