Manuals / Q-Logic / Computer Equipment / Computer Hardware

Q-Logic QLA2300 3. QLA2310FL Board Layout, 4. QLA2302F Board Layout, QLA23xx Board Components

Models: QLA2300

1 30

Download 30 pages 40.11 Kb

Page 11

QLA23xx Board Components

2 – Hardware Installation

QLA23xx Board Components

J2

J2

1 3

NOTE: The serial number is on the other side of the board.

ISP CHIP

Figure 2-3. QLA2310FL Board Layout

ISP CHIP

J1

J2

ISP CHIP

SERIAL NUMBER

Figure 2-4. QLA2302F Board Layout

FC2251101-00 D

2-3

Image 11

Q-Logic QLA2300 3. QLA2310FL Board Layout, 4. QLA2302F Board Layout, QLA23xx Board Components, J2 J2, Isp Chip, J1 J2

Contents

FC2251101-00 D October 5 Hardware Installation Guide for the QLA2300 Board FamilyFibre Channel Host Adapter Boards for the PCI Bus Part of the SANblade Family of ProductsQLogic is a trademark of QLogic Corporation FC2251101-00 D QLogic CorporationPage QLogic Corporation, 26600 Laguna Hills Drive, Aliso Viejo, CA QLogic Corporation2000-2001 QLogic Corporation First Printed July All Rights Reserved Worldwide Printed in U.S.AFast!UTIL Table of ContentsPage FIGURESTABLES PageGeneral Description What is Fibre Channel?Introduction SectionFeatures QLA23xx Board Components Hardware InstallationPreinstallation Procedures What You Need for InstallationSERIAL NUMBER J1 2 - Hardware InstallationFigure 2-1. QLA2300/2310 Board Layout Figure 2-2. QLA2300F/2310F Board LayoutJ2 J2 Figure 2-3. QLA2310FL Board LayoutFigure 2-4. QLA2302F Board Layout QLA23xx Board ComponentsSERIAL NUMBER J1 2 - Hardware InstallationFigure 2-5. QLA2312F Board Layout Figure 2-6. QLA2312FL Board LayoutFigure 2-8. QLA2302F/2312F Board LED Activity LEDs2.3.1 Figure 2-7. QLA2300/2300F/2310/2310F/2310FL Board LED Activity2.3.2 Power DistributionInstallation in the Computer JumpersPCI connectors vary among system board manufacturers. The QLA23xx board is a 64-bit PCI device that can function in a 32-bit PCI slot the slot conforms to the PCI specification the rear edge of the PCI slot is notched. If you try to install the QLA23xx board into a PCI slot that does not conform to the PCI specification, you may damage the QLA23xx board Installation Help System Configuration Problem Checklist TroubleshootingProblems After Installation Hardware Problem ChecklistFibre Channel Problem Checklist Fast!UTIL Configuration SettingsAppendix A IntroductionA.2.1 Host Adapter SettingsSelectable Boot Settings Table A-1. Host Adapter SettingsTable A-2. Advanced Adapter Settings Restore Default SettingsAdvanced Adapter Settings Raw NVRAM DataExecution Throttle. This setting specifies the maximum number of commands executing on any one port. When a port’s execution throttle is reached, no new commands are executed until the current command finishes executing. The valid options for this setting are 1-256. The default is A.2.6 Extended Firmware SettingsTable A-3. Extended Firmware Settings Option Table A-4. RIO Operation ModesTable A-5. Connection Options Operation ModeSelect Host Adapter Scan Fibre Channel DevicesFibre Disk Utility FC2251101-00 D Select Host AdapterA - Fast!UTIL Table B-1. QLA23xx Board Operating Environment SpecificationsAppendix B Table B-2. QLA23xx Board SpecificationsQLA2300/QLA2310 HSSDC connector that supports copper cabling. Fibre Table B-2. QLA23xx Board Specifications ContinuedAppendix C LabelFC2251101-00 D C - Label