Manuals
/
Q-Logic
/
Computer Equipment
/
Computer Hardware
Q-Logic
QLA2300 manual C - Label, FC2251101-00 D
Models:
QLA2300
1
30
30
Download
30 pages
40.11 Kb
23
24
25
26
27
28
29
30
<
>
Troubleshooting
Specification
Install
Configuration Settings
Fibre Channel Problem Checklist
Execution Throttle. This setting specifies the maximum number of commands executing on any one port. When a port’s execution throttle is reached, no new commands are executed until the current command finishes executing. The valid options for this setting are 1-256. The default is
Restore Default Settings
Host Adapter Settings
What is
Power Distribution
Page 30
Image 30
C – Label
C-2
FC2251101-00
D
Page 29
Page 30
Image 30
Page 29
Contents
Part of the SANblade Family of Products
Hardware Installation Guide for the QLA2300 Board Family
Fibre Channel Host Adapter Boards for the PCI Bus
FC2251101-00 D October 5
QLogic is a trademark of QLogic Corporation
QLogic Corporation
Page
FC2251101-00 D
All Rights Reserved Worldwide Printed in U.S.A
QLogic Corporation
2000-2001 QLogic Corporation First Printed July
QLogic Corporation, 26600 Laguna Hills Drive, Aliso Viejo, CA
Table of Contents
Fast!UTIL
Page
FIGURES
TABLES
Page
Section
What is Fibre Channel?
Introduction
General Description
Features
What You Need for Installation
Hardware Installation
Preinstallation Procedures
QLA23xx Board Components
Figure 2-2. QLA2300F/2310F Board Layout
2 - Hardware Installation
Figure 2-1. QLA2300/2310 Board Layout
SERIAL NUMBER J1
QLA23xx Board Components
Figure 2-3. QLA2310FL Board Layout
Figure 2-4. QLA2302F Board Layout
J2 J2
Figure 2-6. QLA2312FL Board Layout
2 - Hardware Installation
Figure 2-5. QLA2312F Board Layout
SERIAL NUMBER J1
Figure 2-7. QLA2300/2300F/2310/2310F/2310FL Board LED Activity
LEDs
2.3.1
Figure 2-8. QLA2302F/2312F Board LED Activity
Jumpers
Power Distribution
Installation in the Computer
2.3.2
PCI connectors vary among system board manufacturers. The QLA23xx board is a 64-bit PCI device that can function in a 32-bit PCI slot the slot conforms to the PCI specification the rear edge of the PCI slot is notched. If you try to install the QLA23xx board into a PCI slot that does not conform to the PCI specification, you may damage the QLA23xx board
Installation Help
Hardware Problem Checklist
Troubleshooting
Problems After Installation
System Configuration Problem Checklist
Fibre Channel Problem Checklist
Introduction
Configuration Settings
Appendix A
Fast!UTIL
Table A-1. Host Adapter Settings
Host Adapter Settings
Selectable Boot Settings
A.2.1
Raw NVRAM Data
Restore Default Settings
Advanced Adapter Settings
Table A-2. Advanced Adapter Settings
Execution Throttle. This setting specifies the maximum number of commands executing on any one port. When a port’s execution throttle is reached, no new commands are executed until the current command finishes executing. The valid options for this setting are 1-256. The default is
Extended Firmware Settings
Table A-3. Extended Firmware Settings
A.2.6
Operation Mode
Table A-4. RIO Operation Modes
Table A-5. Connection Options
Option
Scan Fibre Channel Devices
Fibre Disk Utility
Select Host Adapter
Select Host Adapter
A - Fast!UTIL
FC2251101-00 D
Table B-2. QLA23xx Board Specifications
Specifications
Appendix B
Table B-1. QLA23xx Board Operating Environment
Table B-2. QLA23xx Board Specifications Continued
QLA2300/QLA2310 HSSDC connector that supports copper cabling. Fibre
Label
Appendix C
C - Label
FC2251101-00 D
