General Operations, Turning the Power on and OFF | Raymarine Ray54

Chapter 4: General Operations	17

Chapter 4: General Operations

4.1 Turning the Power ON and OFF

Turn the PWR/VOL knob clockwise until it clicks.

When the unit powers up in Normal mode it:

1.Beeps, illuminates the backlight at full brightness, and displays all seg- ments and indicators for 2 seconds.

2.Displays the software version number on the dot matrix display.

3.Recalls the last CH number, TX power settings and operation mode. If no last-used setting data exists, goes to CH 16 and high TX Power.

When GPS Data is available, extended position data is also displayed with the offset time on the dot matrix display. This information will be displayed when display option for the position and time is enabled on the Menu. See Section 6.6.

To turn the unit OFF, rotate the Volume knob completely counterclockwise until it clicks.

4.2 Setting the Volume

Adjust the PWR/VOL knob to control the loudspeaker volume level. Turn clockwise to increase the volume; counterclockwise to decrease the volume.

Note: Key press beep volume is also controlled by the VOL level.

4.3 Setting the Squelch

The Squelch circuit sets the threshold for cutting off the receiver when the signal is too weak for reception of anything but noise.

To properly set the squelch, rotate the SQ knob counterclockwise until audio is heard. Then rotate clockwise until background noise disappears.

4.4 Setting the Power Output

The choice of power output is dependent upon the distance of transmission and transmitting conditions.

Press and release the HL/USER key on the main unit or microphone to toggle the TX power from LOW (1 watt) to HIGH (25 watts). The corresponding LO or HI indicator appears on the LCD.

Image 27

Raymarine Ray54 manual General Operations, Turning the Power on and OFF, Setting the Volume, Setting the Squelch

Contents

Ray54 Page Conventions Used WarrantyAbout this Handbook Introduction Operator License Important InformationFCC Notice Station License Industry Canada Maritime Mobile Service Identity Mmsi Antenna Mounting and EME Exposure Safe Compass DistanceEMC Conformance Contents CLEAR/WX Distress Digital Selective Calling DSC How to Contact Raymarine Features IntroductionRay54 Fixed Station VHF Radio Digital Selective Calling DSC Installation Unpacking and InspectionEquipment Supplied Planning the Installation Typical Mounting MethodsFlush Mounting Typical Mounting Methods Wiring Connections Power Connections External Speaker Connections GroundingGPS/NMEA Data Antenna Connections Antenna Mounting SuggestionsAntenna Mounting and EME Exposure Keypad and Rotary Knobs Getting Started Microphone Keys Main Unit Rotary KeysMain Unit Push Keys 16/9 MicrophoneMain Unit PTT CALL/MENU HILO/USER 12 /9 LCD Display User Favorite Channel Mode HI/LO TX PowerLocal Local/Distant Mode Battery Low Simplex Channel WX Weather ChannelAlert Weather Alert I C Channel Set Setting the Power Output Turning the Power on and OFFSetting the Volume Setting the Squelch Overriding the Low Output Power Restriction On the main unit Setting the ChannelSelecting a Weather Channel On the microphone Weather Alert Operation Selecting the Priority Channel Selecting the Secondary Priority Channel Reprograming the Secondary Priority Channel Transmitting Using the Scan Modes Saved Memory Scan All Scan Priority All Scan Priority Saved Scan Adding Channels to Memory General Operations Dual Watch Using the Monitor Modes Tri Watch User Channel Mode Menu Mode OperationDSC Call Operation Digital Selective Calling DSC ALL Ships DSC Call FunctionIndividual Group Position RequestRX Call LOG Individual Calls Making DSC Calls to Coast StationsTransmitting an Individual Call If using Manual Mmsi ID entry Ray54 VHF Radio Receiving Individual Calls To cancel the mode without sending ACK Transmitting a Group Call Group Calls Digital Selective Calling DSC Receiving Group Calls To ignore the Group Call Transmitting an All Ships Call All Ships Calls Receiving an All Ships Call To decline the All Ships Call Sending a Distress Call Distress Calls Designated Distress Call Undesignated Quick Distress Call To cancel the automatic Distress resend press CLEAR/WX Receiving a Distress Call Cancelling a Distress Call Made in Error Receiving a Distress Relay Sent by Another Station Receiving a Distress ACK Sent from a Coast Station Specifying the Target Vessel Position Request If using Manual Mmsi ID entry Retrieving the Last Received Position Data When no reply is received within 3 minutes Receiving a Position Request From Another Station Call Log Making a Call from a Call Log Entry Press and hold the SCAN/SAVE key Saving an Mmsi ID Number from a Call Log Entry DSC Distress Log Menu Function Menu Settings Using the Microphone Keys to Make Selections Adding an Entry DSC Phonebook Use same procedure to enter the Mmsi characters Editing an Existing Entry Deleting an Existing Entry Backlight Adjustment Contrast AdjustmentLocal / Distant When GPS Information Not Available GPS/Time Setup Rotate the CH knob to scroll through the selections Settings Menu Settings Time Format Latitude/Longitude DisplayTime Display Time Offset Band Radio Setup Ring Volume Channel CH NameKey Beep DSC Setup My Mmsi ID Group Mmsi Setup Group Name Menu Settings Editing an Existing Entry Position Reply Automatic Channel Changing for Incoming Calls Procedure When Disabled Procedure When Enabled Resetting Factory Defaults On the Internet Customer ServiceHow to Contact Raymarine Product Repair and Service Technical Support Accessories and Parts Appendix a Specifications GeneralPLL Transmitter Receiver Appendix B Channel List Marine VHF Channels and FrequenciesXmit RCV 86Ray54 VHF Radio Freq Use 82A PC, AC, GL Canadian Marine VHF Channels and FrequenciesWC, EC AC, GL AC, GL, PC 156.750 All areas 90Ray54 VHF Radio 156.875 EC, PC AC, GL, NL Area of Operation International Marine VHF Channels & Frequencies 94Ray54 VHF Radio 161.925 WX Channels North America only Appendix C Glossary VHF VOL Numerics Index Mmsi 101 102