Storing a Redial Number | RCA 21011 instruction

STORING A REDIAL NUMBER

1.Make sure the phone is OFF (not in talk mode).

2.Press the DIR soft key.

3.Press any number key (01-50) to store the phone number in that memory location, or press the cid/vol (up and down arrow) button on the handset or CID (up and down arrow) button on the base to select the memory location.

4.Press the EDIT soft key and ENTER NAME shows in the display.

5.Use the touch tone pad on your handset or base to enter the name, then press the OK soft key and ENTER TEL NUMBR shows in the display.

6.Press the redial button to display the redial number.

7.Press the OK soft key again to confirm.

NOTE: If the redial number has more than an 24 digits, the redial number cannot be stored in memory.

INSERTING A PAUSE IN THE DIALING SEQUENCE

If a pause is needed to wait for a dial tone press the # pause button on the number pad to insert a delay in dialing sequence of a stored telephone number (for example, after you dial 9 for an outside line, or wait for a computer access tone.) Each pause counts as one digit in the dialing sequence.

REVIEWING, CHANGING OR DELETING STORED NUMBERS

TO REVIEW:

1.Make sure the phone is OFF (not in talk mode).

2.Press DIR soft key.

NAME

HANDSET 1

MENU DIR

41

Image 41

RCA 21011 manual Storing a Redial Number

Contents

21011 Notification to the LocalTelephone Company Equipment Approval Information Table of Contents Savethese Instructions Introduction Features Your Caller ID Call Waiting phone allows you to Base Layout Handset and Charge Cradle Layout Make sure your package includes the items shown here Before YOU Begin Important Installation Information Installing the Phone Installing the Handset Battery Okexit Telephone SetupLanguage Areacode Setlanguage 1ENG 2FRA 3ESP EnglishLanguage Contrast Exit Contrast SET Areacode AreacodeRingertone Ringer Tone Languageareacode Areacoderingertone SET Tone / Pulse 1 Tone 2 Pulse Okexit Ringer ToneTone / Pulse Time Ringertone Registration Tone Handset Registered Confirm Registration ?Handsetneedsregister Registrationhandset ? Hold Basepage Wait for Beep Menudir Billsmith HandsetEnter Name Billsmith DE-REGISTER Handset 1 ? Movenear TobaseDeregistration Walkietalkie Confirm Deregistration ? Handset Deregistered Deregistration Walkie Talkie Walkie Talkie Enable ?Walkie Talkiewalkie Talkie ENABLEDHANDSET1EXIT Walkie Talkie HANDSET# Handset # DisabledWalkie Talkie Extension ? Walkie Talkie With Handset # SET Time TONE/PULSE Time Defaultsetting YES 2NO Defaultsetting LanguageDefaultsetting Defaultsetting Basic Operation Making a Call Handset Name Handset Ringer on NEW CALL00 Ringer High HI 2LOW 3OFFRinger LOW Conf Trans Exit Line on Hold Paging Extension ? Line ActivePaging Handset Mute Hold DIR Line on Hold Extension ? Pagingfrom HANDSET1 Mute on Pagingfrom HandsetPAGING/LINEONHOLD Steve Temporary Tone Dialing Mute PagingPagingfrom Receiving AN Intercom Call Line on HOLD/INTERCOM PAGING/LINEONHOLDHANDSET1 Memory Select MemoryEdit DEL Exit Menu DIR Enter Telnumbr Storing a Redial Number Delete ? Peter Chan Dialing a Stored Number Handset 000000000000000 Receiving and Storing Call Records You may transfer a Caller ID record to your phone ’s memory Save DEL Exit Replace MEMO? Eleven digits Deleted Delete Call ID? Delete ALL ? No Calls Replacing the Battery Headset and Belt Clip Installation Incomplete Data Display Messages Troubleshooting Guide Handset Sound SignalsPage Caller ID Solutions General Product Care Causes of Poor Reception Service Index Page Orcompletethisorderform For how long after your purchase Limited Warranty