Defaultsetting Language, Defaultsetting YES 2NO | RCA 21011 instruction

DEFAULT

As you become familiar with this system, you may prefer to use the system’s original settings. Follow the steps below to return to the factory default settings.

1.Make sure your handset or base is in menu mode. If your handset or base is not in the menu mode, press the MENU soft key.

2.Press the cid/vol (up and down arrow) button on the handset or CID (up and down arrow) button on the base to move the arrow to DEFAULT SETTING.

DEFAULTSETTING

LANGUAGE

OKEXIT

3.Use the touch tone pad on your handset or base to enter 1YES or 2NO, or use the cid/vol (up or down arrow) button on your handset or the CID (up or down arrow) button on your base to move the arrow to your selection. 2NO is the default setting.

DEFAULTSETTING

1 YES 2NO

OKEXIT

NOTE: If you choose YES all settings in the programmable menu return to the factory default settings.

4.Press the OK soft key to save your selection, and return to the main menu. The default setting you choose shows on the display for two seconds.

DEFAULTSETTING	DEFAULTSETTING
NO	LANGUAGE	EXIT
	OK
HANDSET & BASE DISPLAY	HANDSET & BASE DISPLAY

26

Image 26

RCA 21011 manual Defaultsetting Language, Defaultsetting YES 2NO

Contents

21011 Equipment Approval Information Notification to the LocalTelephone Company Table of Contents Savethese Instructions Features Introduction Your Caller ID Call Waiting phone allows you to Handset and Charge Cradle Layout Base Layout Before YOU Begin Make sure your package includes the items shown here Important Installation Information Installing the Phone Installing the Handset Battery Okexit Telephone SetupLanguage Areacode Language Contrast EnglishSetlanguage 1ENG 2FRA 3ESP Exit Contrast SET Areacode AreacodeRingertone Languageareacode Areacoderingertone Ringer Tone SET Tone / Pulse 1 Tone 2 Pulse Okexit Ringer ToneTone / Pulse Time Tone Ringertone Registration Handsetneedsregister Registrationhandset ? Confirm Registration ?Handset Registered Hold Basepage Wait for Beep Menudir Billsmith HandsetEnter Name Billsmith DE-REGISTER Handset 1 ? Movenear TobaseDeregistration Walkietalkie Handset Deregistered Confirm Deregistration ? Deregistration Walkie Talkie Walkie Talkie Enable ?Walkie Talkiewalkie Talkie ENABLEDHANDSET1EXIT Walkie Talkie Extension ? Handset # DisabledWalkie Talkie HANDSET# Walkie Talkie With Handset # TONE/PULSE Time SET Time Defaultsetting Defaultsetting LanguageDefaultsetting YES 2NO Defaultsetting Basic Operation Making a Call Handset Ringer on Name Handset NEW CALL00 Ringer High HI 2LOW 3OFFRinger LOW Line on Hold Conf Trans Exit Paging Handset Line ActivePaging Extension ? Mute Hold DIR Pagingfrom HANDSET1 Line on Hold Extension ? Mute on Pagingfrom HandsetPAGING/LINEONHOLD Steve Temporary Tone Dialing Mute PagingPagingfrom Receiving AN Intercom Call Line on HOLD/INTERCOM PAGING/LINEONHOLDHANDSET1 Memory Select MemoryEdit DEL Exit Enter Telnumbr Menu DIR Storing a Redial Number Peter Chan Delete ? Dialing a Stored Number Handset 000000000000000 Receiving and Storing Call Records Save DEL Exit You may transfer a Caller ID record to your phone ’s memory Replace MEMO? Eleven digits Delete Call ID? Deleted No Calls Delete ALL ? Replacing the Battery Headset and Belt Clip Installation Display Messages Incomplete Data Handset Sound Signals Troubleshooting GuidePage Caller ID Solutions General Product Care Service Causes of Poor Reception Index Page Orcompletethisorderform Limited Warranty For how long after your purchase