Regency I31-LPG3 Copy of Lighting Instruction Plate, Maintenance Instructions, Pilot Flame

OPERATING INSTRUCTIONS

COPY OF LIGHTING INSTRUCTION PLATE

FORYOURSAFETYREADBEFORELIGHTING

This appliance must be installed in accordance with local codes, if any; if none, follow the National Fuel Gas Code, ANSI Z223.1/NFPA 54,

or Natural Gas and Propane Installations Codes, CSA B149.1. (Australia: AS5601-2004/ New Zealand: NZS 5261)

WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life. Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Refer to the owner’s information manual provided with this appliance. For assistance or additional information consult a qualified installer, service agency or gas supplier.

MAINTENANCE INSTRUCTIONS

1) Always turn the gas valve to off

before cleaning. For relighting, re-

fer to lighting instructions. Keep the

burner and control compartment

clean by brushing and vacuuming

at least once a year.

When cleaning the logs, use a clean

A)This appliance has a pilot which must be lighted by hand, following the instructions below exactly.

B)BEFORE LIGHTING smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor.

WHAT TO DO IF YOU SMELL GAS:

-Do not try to light any appliance.

-Do not touch any electric switch, do not use any phone in your building.

-Immediately call your gas supplier from a neighbors phone. Follow the gas supplier’s

instructions.

-If you cannot reach your gas supplier, call the fire department.

C)Use only your hand to push in or turn the gas control knob. Never use tools. If the knob will not push in or turn by hand, do not try to repair it, call

a qualified service technician. Force or attempted repair may result in a fire or explosion.

D)Do not use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water.

This appliance needs fresh air for safe operation and must be installed so there are provisions for adequate combustion and ventilation air.

CAUTION: Hot while in operation. Do not touch. Severe Burns may result. Due to high surface temperatures keep children, clothing and furniture, gasolineandotherliquidshavingflammablevapors away. Keep burner and control compartment clean. See installation and operating instructions accompanying appliance.

soft paint brush as the logs are

fragile and easily damaged.

2) Clean (never when unit is hot) ap-

pliance, door and louvres with a

damp cloth. Never use an abrasive

cleaner. The gold louvres (and

optional gold door) may be

scratched if abrasives are used to

clean them.

The heater is finished in a heat

resistant paint and should only be

refinished with heat resistant paint

(not with wall paint). Regency uses

StoveBrite Paint - Metallic Black

#6309.

LIGHTING INSTRUCTIONS

STOP! Read the safety information above on this label.

1)Push in gas control knob slightly and turn

clockwise to “OFF”. Knob cannot be turned from “PILOT” to “OFF” unless knob is pushed in slightly. Do not force.

2)Wait five (5) minutes to clear out any gas. If you then smell gas STOP! follow “B” in the safety information above on this label. If you do not smell gas, go to the next step.

3)Turn knob on gas control counterclockwise

to “PILOT” .

4)Push in control knob all the way and hold in. Immediately push black button on spark igniter until pilot lights. Continue to hold the control knob in for about 1/2 minute after the pilot is lit.

Release knob and it will pop back up. Pilot should remain lit. If it goes out, repeat steps 3) and 4). If knob does not pop up when released, stop and immediately call your service technician or gas supplier. If the pilot will not stay lit after several tries, turn the gas control knob to “OFF” and call

your service technician or gas supplier.
5) Turn gas control knob counterclockwise	to
“ON”.
6) Use rocker switch to operate main burner.

3)	Make a periodic check of burner for
	proper position and condition. Vis-
	ually check the flame of the burner
	periodically, making sure the flames
	are steady; not lifting or floating. If
	there is a problem, call an author-
	ised service person.
4)	The appliance and flueing system
	must be inspected before use, and
	at least annually, by an authorised
	field service person, to ensure that
	the flow of combustion and venti-
	lation air is not obstructed.

TO TURN OFF GAS APPLIANCE

1) Push in the gas control knob slightly and turn		2) Turn off all electric power to the appliance if
clockwise	to “OFF”. Do not force.	service is to be performed.

You may shut off the pilot during prolonged non use periods to conserve fuel.

DO NOT REMOVE THIS INSTRUCTION PLATE 908-401c

During the annual service call, the

burners should be removed from

the burner tray and cleaned. Re-

place the embers but do not block

the pilot.

Pilot Flame:

While the pilot flame is on it can make a very slight "whisper" sound.

Gas Control Valve:

As the gas control valve turns ON and OFF, a dull clicking sound may be audible, this is normal operation of a gas regulator or valve.

Unit Body/Firebox:

Different types and thicknesses of steel will expand and contract at different rates resulting in some "cracking" and "ticking" sounds will be heard throughout the cycling process.

ANY SERVICING OR REPAIRS SHOULD BE CARRIED

OUT ONLY BY AN

AUTHORISED

PERSON.

5)Keep the area near the appliance clear and free from combustible materials, gasoline and other flam- mable vapours and liquids.

WARNING: CHILDREN AND ADULTS SHOULD BE ALERTED TO THE HAZARDS OF HIGH SUR- FACE TEMPERATURE AND SHOULD STAY AWAY TO AVOID BURNS OR CLOTHING IGNITION. YOUNG CHILDREN SHOULD BE CAREFULLYSUPERVISEDWHEN THEYAREINTHESAMEROOMAS THE APPLIANCE.

Regency I31-3 Gas Fireplace Inbuilt 17