OPERATING INSTRUCTIONS
COPY OF LIGHTING INSTRUCTION PLATE
FOR YOUR SAFETY READ BEFORE LIGHTING 
This appliance must be installed in accordance with local codes, if any; if not,
follow the current
WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life. Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Refer to the owner’s information manual provided with this appliance. For assistance or additional information consult a qualifi ed installer, service agency or gas supplier.
NORMAL OPERATING
SOUNDS OF
GAS APPLIANCES
It is possible that you will hear some sounds from your gas appliance. This is perfectly normal due to the fact that there are various gauges and types of steel used within your appliance. Listed below are some examples.All are normal operating sounds and should not be considered as defects in your appliance.
A)BEFORE LIGHTING smell all around the appliance area for gas. Be sure to smell next to the fl oor because some gas is heavier than air and will settle on the fl oor.
WHAT TO DO IF YOU SMELL GAS
-Do not try to light any appliance
-Do not touch any electric switch, do not use any phone in your building
-Immediately call your gas supplier from a neighbors phone. Follow the gas supplier’s instructions.
-If you cannot reach your gas supplier, call the fi re department.
B)Do not use this appliance if any part has been under water. Immediately call a qualifi ed service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water.
This appliance needs fresh air for safe operation and must be installed so there are provisions for adequate combustion and ventilation air.
Blower:
Regency gas appliances use high tech blowers to push heated air farther into the room. It is not unusual for the fan to make a "whirring" sound when ON. This sound will increase or decrease in volume depending on the speed setting of your fan speed control.
CAUTION: Hot while in operation. Do not touch. Severe Burns may result. Due to high surface temperatures keep children, clothing and furniture, gasoline and other liquids having fammable vapors away. Keep burner and control compartment clean. See installation and operating instructions accompanying appliance.
LIGHTING INSTRUCTIONS
STOP! Read the safety information above on this label.
1) | Plug the power cord into a power outlet. | 3) | After approximately 8 seconds the spark ignition |
|
|
| system will spark for 8 seconds to light the main |
2) | Press and release the ON/OFF switch once to start |
| burner. |
| the unit. The LED will be lit. | 4) | If the main burner does not light, repeat step 2 to |
|
| ||
|
|
| restart. |
|
|
| TO TURN OFF GAS APPLIANCE |
|
| 1) Press the ON/OFF switch once. | 3) Turn off all electric power to the unit if service is | ||
to be performed.
2)The LED will flash.
You may shut off the pilot during prolonged non use periods to conserve fuel.
DO NOT REMOVE THIS INSTRUCTION PLATE | |
|
WARNING:
DO NOT SPRAY AEROSOLS IN THE VICINITY OF
THIS APPLIANCE WHILE IN OPERATION.
"Appliances incorporating a live fuel effect, and designed to operate with luminous flames, may exhibit slight carbon deposition."
Burner Tray:
The burner tray is positioned directly under the burner tube(s) and logs and is made of a differ- ent gauge material from the rest of the firebox and body. Therefore, the varying thicknesses of steel will expand and contract at slightly different rates which can cause "ticking" and "cracking" sounds. You should also be aware that as there are temperature changes within the unit these sounds will likely
Gas Control Valve:
As the gas control valve turns ON and OFF, a dull clicking sound may be audible, this is normal operation of a gas regulator or valve.
Unit Body/Firebox:
Different types and thicknesses of steel will expand and contract at different rates resulting in some "cracking" and "ticking" sounds will be heard throughout the cycling process.
RESETTING THE UNIT
If the appliance goes to 'lockout', the system will have to be reset by depressing the reset button - located behind bottom louver.
*Important: Wait at least 5 min for any un- burned gas to clear before resetting the appliance.
1)Open the bottom louver on the unit.
2)Press and release the reset button - once. The button is located near the gas valve.
3)Wait for approximately 3 seconds - the pilot sparks can be heard and seen. It will take approximately 2 to 3 seconds for the flame to be lit.
NOTE: Wait 30 seconds between reset attempts.
24 | Regency IG34 Gas Inbuilt Fireplace |
