Regency IG34-LPG, IG34-ULPG, IG34-NG installation manual Installation

INSTALLATION

IMPORTANT MESSAGE

The Regency Gas Inbuilt must be installed in accordance with these instructions. Carefully read all the instructions in this manual first.

Note: Failure to follow these instructions could cause a malfunction of the heater which could result in death, serious bodily injury, and/or prop- erty damage. Failure to follow these instructions may also void your fire insurance and/or warranty.

FOR YOUR SAFETY

This appliance requires air for proper combus- tion. Always provide adequate combustion and ventilation air. Follow instructions and information in the current AS5601, NZS 5262 or local codes. Consult the "authority having jurisdiction" to determine the need for a permit prior to starting the installation.

MATERIALS REQUIRED

A 240 Volt AC power cord is hooked up to the unit. Plug 3 wire cord into a suitable receptacle. Do not cut the ground terminal off under any circumstances.

When connected with 240 volts, the appliance must be electrically grounded in accordance with local codes.

This unit is polarity sensitive and will not operate if polarity is incorrect.

BEFORE YOU START

Installation is to be carried out ONLY by an authorised person.

1)The appliance shall be installed in accord- ance with the manufacturer's installation instructions, local gas fitting regulations, municipal building codes, water supply regulations, electrical wiring regulations, with AS5601. (AGA gas installation code) NZS 5262(New Zealand)

2)Installation and repair should be done ONLY by an authorised person.

3)The appliance should be inspected before use and at least annually by an authorised service person. More frequent cleaning may be required due to excessive lint from carpet- ing, bedding material, etc. It is imperative that control compartments, burners and circulating air passageways of the appliance be kept clean and free from excessive lint from carpeting.

4)See general construction and assembly instructions. This appliance may only be in- stalled in a flued, non-combustible fireplace. The appliance and flue should be enclosed when installed or passing through a living area, where children may come in contact with it.

5)Always connect this space heater to a chim- ney and flue to the outside of the building envelope. Never flue to another room. Make sure that the flue is properly sized and is of adequate height to provide the proper draft.

6)Inspect the flueing system annually for blockage and any signs of deterioration.

7)Any safety glass removed for servicing must be replaced prior to operating the ap- pliance.

INSTALLATION

CHECKLIST

Before installing vent system ensure that the damper plate is open and secure to prevent the damper plate from falling down and crushing the liner.

The FPI Gas Inbuilt is installed as listed.

1)	Check all clearances to combustibles, (Refer
	to sections "Minimum Fireplace Dimensions
	and Clearances to Combustibles)
2)	Make the gas connection. (Refer to section
	"Gas Connection")
3)	Install the 3" (76.2mm) flue liner to the sliding
	connector plate. (Refer to section "Flue Liner
	Installation.")
4)	Slide the unit half way into the fireplace.
5)	Pull the vent connector plate through the
	tapered brackets and fasten to the front plate.
	Refer to section "Flue Liner Installation.")
6)	Slide the unit fully into the fireplace.
7)	Test gas pressure (Refer to section "Gas
	Pipe Pressure Testing"). Check aeration
	system (Refer to section "Gas InsertAeration
	System").
8)	Install standard and optional features. Refer
	to the following sections:
	a. Log Set
	b. Faceplate & Door Trim
	c. Inner Stainless Panels
9)	Final check: Before leaving this unit with the
	customer, the installer must ensure that the
	appliance is firing correctly. This includes:
	a) Clocking the appliance to ensure the
	correct firing rate.

WARNING:

Suitable for installation into a masonry fireplace only.

8)To prevent injury, do not allow anyone who is unfamiliar with the operation to use the fireplace.

9)Installer must mechanically attach the sup- plied label to the inside of the firebox of the fireplace into which the gas fireplace insert is installed.

"WARNING: This fireplace has been converted for use with a gas fireplace insert only and cannot be used for burning wood or solid fuels unless all original parts have been replaced, and the fireplace re-approved by the authority having jurisdiction."

b) Adjusting the primary air and restrictor

settings, if required, to ensure that the

flame does not carbon.

NOTE:

TO BE INSTALLED ON A

NON- COMBUSTIBLE FLOOR.

Regency IG34 Gas Inbuilt Fireplace 5