Manuals
/
Brands
/
Computer Equipment
/
Network Card
/
Renesas
/
Computer Equipment
/
Network Card
Renesas
E8
- page 110
1
110
164
164
Download
164 pages, 2.5 Mb
6.2 Running the High-performance Embedded Workshop
To run the High-performance Embedded Workshop, refer to section 3.8, System Check.
6.3 Setting up the E8 Emulator
This section describes the basic settings of the emulator.
94
Contents
Main
E8 Emulato
r
User's Manual R0E000080KCE00E
Rev.10.00 Aug. 1, 2007
Notes regarding these materials
Introduction
Page
IMPORTANT
READ FIRST
Page
Page
DEFINITION OF SIGNAL WORDS
DANGER
NOTE
WARNING
WARNING
CAUTION
Page
Contents
Page
Page
Page
Page
Page
Section 1 Overview
Page
Page
1.2 Environmental Conditions
Table 1.1 Environmental Conditions
Table 1.2 Operating Environments
Page
Page
Section 2 E8 Emulator Functions
2.1 Overview
Table 2.1 gives a functional overview of the emulator. Table 2.1 Emulator Functions
Table 2.1 Emulator Functions (cont)
The specific functions of the emulator are described in the next section.
Page
2.3 Break Functions
2.4 Memory Access Functions
2.5 Stack Trace Function
2.6 Online Help
Section 3 Preparation before Use
3.1 Emulator Preparation
Unpack the emulator and prepare it for use as follows:
Figure 3.1 Emulator Preparation Flow Chart
Page
Page
Page
Page
Page
3.3 Emulator Software Configuration
Page
Page
Page
3.6 Connecting the Emulator to the User System
Connector for user system interface cable
Page
3.7 Connecting System Ground
Figure 3.10 Connecting System Ground
3.8 System Check
Page
Page
Page
Page
Page
Page
Page
Page
3.9 Uninstalling the Emulators Debugger
Page
Page
Page
Section 4 Preparations for Debugging
4.1 Method for Activating High-performance Embedded Workshop
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
4.2 Setting at E8 Emulator Activation
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Section 5 Debugging
5.1 Setting the Environment for Emulation
Page
Page
5.2 Downloading a Program
Page
Page
Page
5.3 Stopping Your Program
5.4 Using the Event Points
Page
Page
Page
Page
Page
Page
The [Address] group box sets address bus conditions.
The contents of an option that can be will change depending on the radio button selected.
The [Data] group box sets the data bus conditions.
The [Read/Write] group box sets the read/write cycle conditions.
5.5 Viewing the Trace Information
Page
5.6 Using the Start/Stop Function
Page
Page
Page
Section 6 Tutorial
6.1 Introduction
Page
Page
Page
6.5 Checking the Operation of RAM
Page
6.6 Downloading the Tutorial Program
Page
6.7 Setting a PC Breakpoint
Page
Page
6.9 Executing the Program
Page
Page
6.10 Reviewing Breakpoints
6.11 Viewing Memory
6.12 Watching Variables
Page
Page
6.13 Stepping Through a Program
Page
Page
6.14 Forced Breaking of Program Executions
6.15 Displaying Local Variables
6.16 Break Function
Page
Page
Page
6.17 Hardware Break Function
Page
Page
6.18 Trace Functions
6.19 Stack Trace Function
Page
Page
Page
Appendix A Components of the E8 Emulator
Page
Appendix B Window Functions
Page
Table B.1 Window Functions (cont)
Page
Page
Page
Appendix D Notes on High-performance Embedded Workshop
Page
Page
Page
Page
Page
Appendix E Diagnostic Hardware Program
E.1. System Setup to Execute the Check Program
E.2. Executing the Check Program
Page
E.3 When an Error Occurs
