Manuals / Roberts Gorden / Household Appliance / Gas Heater

Roberts Gorden BH Series Line Voltage Thermostat Wiring, Electrical Shock Hazard

Models: BH Series

1 41

Download 41 pages 53.69 Kb

Page 36

Image 36

ROBERTS GORDON ® BH-SERI E S SUBM IT TAL SHE E T

WIRING

WARNING

Electrical Shock Hazard

Disconnect electrical power and gas supply before servicing.

This appliance must be connected

to a properly grounded electrical source.

Failure to follow these instructions can result in death or electrical shock.

Line Voltage Thermostat Wiring

	Line Voltage Thermostat
120V-60Hz
Supply Circuit
L1				Additional
				Additional
L2				Burners
L2
Gnd.	N	H	N	H
Gnd.
		Gnd.		Gnd.
				Maximum 5 Burners
				Per Thermostat
	Burner 1	Burner 2

© 2004 Roberts-Gordon	BEFORE IN STALLATI ON AND OPER ATI ON OF HEATI NG EQUIPMENT, READ AND U NDERSTAND THE INSTALLATION, OPERATIO N AND SERVICE MANUAL .
© 2004 Roberts-Gordon	APPLICATION S, ENGI NEERING AND DETAI LED GUID ANCE ON SYSTEMS DESIGN, INSTALLATI ON AND PRODUCT PERFORMANCE IS AVAI LABLE UPON REQUEST. ROBERTS GORDON® PRODUCTS ARE TO BE
	INSTALLED ONLY IN ACCORDANCE WI TH LOCAL LAWS, CODES AND REGULATIONS, AND ONLY BY A CONTRACTOR QUALI FIED I N THE I NSTALLATION AND SERVICE OF GAS-FIRED HEATING EQUI PMENT.

Page 36

Image 36

Roberts Gorden BH Series Line Voltage Thermostat Wiring, Electrical Shock Hazard, This appliance must be connected

Contents

GordonRay BH The Economical, Unitary Infrared HeaterSubmittal BH Series TABLE OF CONTENTS 2004STANDARD PARTS LIST Contents of BH-SeriesBurner CartonContents of Core and Extension Packages End View GENERAL SPECIFICATIONS Material SpecificationCLEARANCES TO COMBUSTIBLES 45 Tilt Reflector U-Tube,Opposite 45 Reflector Venting inchescentimeters ModelBH-SERIESASSEMBLY OVERVIEW BH-SeriesLinear Assembly Overview HEATER INSTALLATION Critical Hanger Placement Typical Suspension DetailsBH-40 BH-60BH-80 BH-80BH-140 BH-150BH-175 BH-200Tube Clamp Package Installation Coupling and Tube AssemblyFlat Washerdimensions ± 2 5 cmDrive Slide Bar until tight End of Slide Bar should beTurbulator Installation Reflector InstallationOption B Option AOption A Option BBurner Installation Extra chain min 12 30 cmBurner GasketU-Tube,Standard U-Tube,FullU-Tube,Opposite Tight U-BoltBH-60 BH-80BH-80 BH-100BH-140 BH-150BH-175 BH-200Description Part NumberElbow Package 02718702Reflector Joint Installation Reflector Joint DetailReflector Joint Detail ReflectorBracket Installation Side Reflector InstallationREFLECTOR SIDE EXTENSION LOWER CLEARANCE SHIELD INSTALLATION Shield Support Strap AssemblyTWO-FOOTDECORATIVE GRILLE INSTALLATION Grille InstallationDescription Distance AExtension DescriptionONE-FOOTDECORATIVE GRILLE INSTALLATION One-FootDecorative Grille BracketIn order to maintain reflector shape, do Decorative GrilleEnd Piece and Reflector End Cap 90 ElbowReflector End Cap End Piece Insert end piece between grille and bracketsGrille End Cap Installation DescriptionPart Number Grille End CapVENTING Horizontal Ventilation 4 10 cm Pipe Vertical Ventilation 4 10 cm PipeCombustible or Non-CombustibleWall OnlyCommon Sidewall Venting Outside WallCommon Vertical Venting Top ViewOUTSIDE COMBUSTION AIR SUPPLY Outside Wall GAS PIPING WIRING Line Voltage Thermostat WiringElectrical Shock Hazard This appliance must be connectedElectrical Shock Hazard This appliance must be connectedto a properly grounded electrical source SPDT Transformer RelayTransformer Pressure Switch Gap Electrode Ground Power Sense Spark ValvePressure Switch BlowerConnect Wires together with Conduit Hole BX or Romex ConnectorInternal Wire Bundle Burner Box Green to GndMica Window Assembly Burner Cup Assembly Transformer Gas ValveBlower Assemby DSI Ignition Module Blower Outlet GasketTHE ROBERTS GORDON GORDONRAY BH LIMITED WARRANTY WARRANTY IS VOID IFROBERTS-GORDONWILL PAY FOR ROBERTS-GORDONWILL NOT PAY FOR