208
Adding Effects

Tone Output Assign

Specifies how the direct sound of each tone will be output.

Value:
MFX:

Output in stereo through multi-effects. You can also
apply chorus or reverb to the sound that passes
through multi-effects.

A, B:

Output to the OUTPUT A (MIX) jack or OUTPUT B
jack in stereo without passing through multi-effects.

1–4:

Output to the INDIVIDUAL 1–4 jacks in mono
without passing through multi-effects.

If the Patch Output Assign ( ) is set to anything other than
“TONE,” these settings will be ignored.
• When the Structure Type parameter has a setting of Type “2”–
”10,” the outputs of tones 1 and 2 will be combined with tone 2,
and the outputs of tones 3 and 4 will be combined with tone 4.
For this reason, tone 1 will follow the settings of tone 2, and
tone 3 will follow the settings of tone 4 (p. 63).
• If you've made settings so that sounds are separately routed to
the INDIVIDUAL 1 jack and INDIVIDUAL 2 jack, but no plug
is actually inserted in the INDIVIDUAL 2 jack, the sounds
routed to INDIVIDUAL 1 and INDIVIDUAL 2 will be mixed
and output from the INDIVIDUAL 1 jack.

If the Mix/Parallel parameter is set to “MIX,” all sounds are
output from the OUTPUT A (MIX) jacks in stereo (p. 230).

If you've set Tone Out Assign to “MFX,” set the MFX Output
Assign parameter ( ) to specify the output destination of the
sound that has passed through the multi-effects.
• Chorus and reverb are output in mono at all times.
• The output destination of the signal after passing through the
chorus is set with the Chorus Output Select ( ) and the
Chorus Output Assign ( ).
• The output destination of the signal after passing through the
reverb is set with the Reverb Output Assign ( ).

Tone Output Level

Set the level of the signal that is sent to the output destination
specified by Output Assign ( , ).
Value:
0–127

Tone Chorus Send Level

Sets the level of the signal sent to chorus for each tone.

Value:

0–127

Tone Reverb Send Level

Sets the level of the signal sent to reverb for each tone.

Value:

0–127

MFX Type (Multi-Effects Type)

Use this parameter to select from among the 78 available multi-
effects. For details on multi-effects parameters, refer to

“Multi-
Effects Parameter”

(p. 270).

Value:

0 (Through)–78

MFX Output Level (Multi-Effects Output

Level)

Adjusts the volume of the sound that has passed through the
multi-effects.

Value:

0–127

MFX Chorus Send Level (Multi-Effects

Chorus Send Level)

Adjusts the amount of chorus for the sound that passes through
multi-effects. If you don’t want to add the Chorus effect, set it to
“0.”

Value:

0–127

MFX Reverb Send Level (Multi-Effects

Reverb Send Level)

Adjusts the amount of reverb for the sound that passes through
multi-effects. If you don’t want to add the Reverb effect, set it to
“0.”
Value:
0–127

MFX Output Assign (Multi-Effects Output

Assign)

Adjusts the output destination of the sound that has passed
through the multi-effects.

Value
A:

Output to the OUTPUT A (MIX) jacks in stereo.

B:

Output to the OUTPUT B jacks in stereo.

If the Mix/Parallel parameter is set to “MIX,” all sounds are
output from the OUTPUT A (MIX) jacks in stereo (p. 230).

Chorus Type

Selects either chorus or delay.

Value
0 (Off):

Neither chorus or delay is used.

1 (Chorus):

Chorus is used.

2 (Delay):

Delay is used.

3 (GM2 Chorus):

General MIDI 2 chorus

3

2
11
13
15
18

4

2 3

5

6

7

8

9

10

11

12

Fantom-X678_r_e.book 208 ページ ２００５年５月１２日　木曜日　午後４時４０分