275
Effects List

15: RING MODULATOR

This is an effect that applies amplitude modulation (AM) to the input
signal, producing bell-like sounds. You can also change the
modulation frequency in response to changes in the volume of the
sound sent into the effect.

fig.MFX-15

16: STEP RING MODULATOR

This is a ring modulator that uses a 16-step sequence to vary the
frequency at which modulation is applied.

fig.MFX-16

17: TREMOLO

Cyclically modulates the volume to add tremolo effect to the sound.

fig.MFX-17a

18: AUTO PAN

Cyclically modulates the stereo location of the sound.

fig.MFX-18a

19: STEP PAN

This uses a 16-step sequence to vary the panning of the sound.

fig.MFX-19

Parameter Value Description

Frequency # 0–127 Adjusts the frequency at which modula-
tion is applied.
Sens # 0–127 Adjusts the amount of frequency modu-
lation applied.
Polarity UP, DOWN Determines whether the frequency mod-
ulation moves towards higher frequen-
cies (
UP
) or lower frequencies (
DOWN
).
Low Gain -15– +15 dB Gain of the low frequency range
High Gain -15– +15 dB Gain of the high frequency range
Balance # D100:0W–
D0:100W Volume balance between the direct
sound (D) and the effect sound (W)
Level 0–127 Output level

Parameter Range Explanation

Step 01–16 0–127 Frequency of ring modulation at
each step
Rate # 0.05–10.00 Hz, note Rate at which the 16-step se-
quence will cycle
Attack # 0–127 Speed at which the modulation
frequency changes between
steps
Low Gain -15– +15 dB Amount of boost/cut for the
low-frequency range
High Gain -15– +15 dB Amount of boost/cut for the
high-frequency range
Balance # D100:0W–
D0:100W Volume balance of the original
sound (D) and effect sound (W)
Level 0–127 Output volume
L in
R in
L out
R out

Ring Mod

2-Band EQ
2-Band EQ

Ring Mod

L in
R in
L out
R out
Step Ring Mod
2-Band EQ
2-Band EQ
Step Ring Mod
L in
R in
L out
R out

Tremolo

2-Band EQ
2-Band EQ

Tremolo

Parame-
ter
Value Description

Mod Wave TRI, SQR, SIN,
SAW1, SAW2 Modulation Wave
TRI:
triangle wave
SQR:
square wave
SIN:
sine wave
SAW1/2:
sawtooth wave
Rate # 0.05–10.00 Hz, note Frequency of the change
Depth # 0–127 Depth to which the effect is applied
Low Gain -15– +15 dB Gain of the low range
High Gain -15– +15 dB Gain of the high range
Level 0–127 Output Level

Parame-
ter
Value Description

Mod Wave TRI, SQR, SIN,
SAW1, SAW2 Modulation Wave
TRI:
triangle wave
SQR:
square wave
SIN:
sine wave
SAW1/2:
sawtooth wave
Rate # 0.05–10.00 Hz, note Frequency of the change
Depth # 0–127 Depth to which the effect is applied
Low Gain -15– +15 dB Gain of the low range
High Gain -15– +15 dB Gain of the high range
Level 0–127 Output Level

Parameter Range Explanation

Step 01–16 L64–63R Pan at each step
Rate # 0.05–10.00 Hz, note Rate at which the 16-step se-
quence will cycle
Attack # 0–127 Speed at which the pan changes
between steps
Input Sync
Sw OFF, ON Specifies whether an input note
will cause the sequence to re-
sume from the first step of the se-
quence (ON) or not (OFF)
Input Sync
Threshold 0–127 Volume at which an input note
will be detected
Level 0–127 Output volume
SAW1 SAW2
L in
R in
L out
R out

Auto Pan

2-Band EQ
2-Band EQ

Auto Pan

SAW1 SAW2
L
R
L
R
L in
R in
L out
R out
Step Pan
Step Pan
Fantom-X678_r_e.book 275 ページ ２００５年５月１２日　木曜日　午後４時４０分