240

Installing the Wave Expansion Board

Up to four optional Wave Expansion Boards (SRX series; sold
separately) can be installed in the Fantom-X.
Wave Expansion Boards store Wave data, patches, and rhythm sets,
and by equipping the Fantom-X with these boards, you can greatly
expand your sound palette.

901

• To avoid the risk of damage to internal components that can be
caused by static electricity, please carefully observe the
following whenever you handle the board.

1

• Before you touch the board, always first grasp a metal object
(such as a water pipe), so you are sure that any static
electricity you might have been carrying has been
discharged.

2

• When handling the board, grasp it only by its edges. Avoid
touching any of the electronic components or connectors.

5

• Save the bag in which the board was originally shipped, and
put the board back into it whenever you need to store or
transport it.
• Use a Phillips screwdriver that is suitable for the size of the
screw (a number 2 screwdriver, Fantom-X6/X7 only). If an
unsuitable screwdriver is used, the head of the screw may be
stripped.
• To remove a screw, rotate the screwdriver counter-clockwise.
To tighten the screws, rotate the screwdriver clockwise.

fig.30-001.e

• When installing Wave Expansion Boards, remove only the
specified screws.
• Be careful that the screws you remove do not drop into the
interior of the Fantom-X.
• Do not leave the bottom cover removed. After installation of the
Wave Expansion Boards is complete, be sure to replace the
cover.
• Be careful not to cut your hand on the opening for installing the
board.
• Do not touch any of the printed circuit pathways or connection
terminals.

911

• Do not touch any of the printed circuit pathways or connection
terminals.

912

• Never use excessive force when installing a circuit board. If it
doesn’t fit properly on the first attempt, remove the board and
try again.

913

• When circuit board installation is complete, double-check your
work.

914

• Always turn the unit off and unplug the power cord before
attempting installation of the circuit board (SRX series).

915

• Install only the specified circuit board(s) (SRX series). Remove
only the specified screws.
Install the Wave Expansion Boards after removing the panel cover.
Boards can be installed in the EXP A–EXP D slots. These slots
correspond with the Wave Expansion Board groups (XP-A–XP-D)
when the expansion Wave, patches, and rhythm sets are used.

1.

Before installing the Wave Expansion Board, turn off the
power of the Fantom-X and all connected devices, and
disconnect all cables, including the Power cable, from the
Fantom-X.

2.

From the Fantom-X, remove only the screws shown in the
following diagram, and detach the cover. On the Fantom-
X6/X7, the cover is located on the bottom panel. On the
Fantom-X8, it is located on the front panel.

* A hex wrench is included with the Fantom-X8. When removing
screws, you must use this hex wrench.

fig.30-002.e
fig.30-003.e

When turning the unit upside-down, get a bunch of newspapers
or magazines, and place them under the four corners or at both
ends to prevent damage to the buttons and controls. Also, you
should try to orient the unit so no buttons or controls get
damaged.
When turning the unit upside-down, handle with care to avoid
dropping it, or allowing it to fall or tip over.

Cautions When Installing an

Wave Expansion Board

tightenloosen

How to Install a Wave

Expansion Board

Screws to be removed
Fantom-X6/X7 : bottom
Fantom-X8 : Front
5mm Hexagonal Wrench
Screws to be removed
Fantom-X678_r_e.book 240 ページ ２００５年５月１２日　木曜日　午後４時４０分