Royal Appliance M5036_5037 manual Operation

M5036_5037.book Seite 10 Freitag, 28. Januar 2011 6:01 18

Operation

2 Operation

2.1Unpacking

1.Unpack the appliance with all its accesso- ries.

2.Check the contents for completeness and possible damages. For scope of delivery see figs. 1–4.

NOTE:

Immediately contact your dealer if you have found damage resulting from transport.

ATTENTION:

Always transport or ship the appliance in its original packaging to avoid damage. Keep the packaging for such an event.

Dispose of no longer needed packaging material properly.

2.2Assembly

WARNING:

Danger of injury! Only assemble the appli- ance if it is not connected to the power sup- ply. Otherwise the machine might start up and parts of your body, hair or pieces of clothing might be sucked in.

1.Push the end of the suction hose into the socket (Fig. 6/A) as shown until the catch snaps into place. Make sure that the catch is on the upper side.

2.Insert the handle into the upper end of the telescopic tube (Fig. 6/B).

AB

6

3.Push the nozzle onto the lower end of the telescopic tube (Fig. 7/A).

4.Adjust the length of the telescopic tube. To do this, press the telescopic tube lock down (Fig. 7/B). Then extend the telescopic tube to your desired length. To engage the lock of the telescopic tube, release the catch while pulling. You will hear a distinct click.

A B

7

Your vacuum cleaner is now ready for use.

2.3Vacuum cleaning

WARNING:

Danger of injury! A damaged appliance must never be used. Check the cylinder vacuum cleaner and the power cord before each use.

WARNING:

Danger of injury! Especially when vacuum- cleaning stairs make sure that you are always higher up than the appliance.

ATTENTION:

Only use the cylinder vacuum cleaner with all filters intact, in dry condition and correctly placed. Make sure that the openings of the vacuum cleaner are not clogged. Otherwise the vacuum cleaner might be damaged.

1.Attach the desired nozzle to the suction tube or according to the surface to be cleaned (Fig. 2 or Fig. 4).

2.Pull out the power cord by the plug up to the yellow mark (Fig. 8/4).

WARNING:

Danger of electric shock! If the red mark (Fig. 8/3) shows, retract the cord by pressing the retract button (Fig. 8/1) to pull in the cable up to the yellow mark again. Otherwise the cord might break.

1

2

3

4

8

3.Insert the mains plug into a socket with ground/safety contact.

4.Switch on the cylinder vacuum cleaner with the on/off switch (Fig. 8/2).

5.Set the carpet/hard floor switch (Fig. 3/1) according to the type of flooring:

-for deep- and short-pile carpets, runners (Fig. 3/A)

-for hard floors, e.g. laminate, tiles, PVC, etc. (Fig. 3/B).

6.When working with the cylinder vacuum cleaner, pull if after you like a sleigh. Follow the respective recommendations of the flooring manufacturers.

NOTE:

With the bypass vent (Fig. 1/4) you can quickly reduce the suction power if less power is needed, e. g. to release objects accidentally sucked in.

2.4Switching off

1.Switch off the cylinder vacuum cleaner with the on/off switch (Fig. 8/2) and pull the plug from the mains socket.

2.Keep the plug in your hand.

WARNING:

Danger of injury! During uncontrolled retrac- tion the power cord can whip around, become an obstacle or overthrow objects. Therefore keep the plug in your hand and guide it during retraction of the power cord.

3.Push the cord retracting button (Fig. 8/1) to retract the power cord.

2.5Transportation

For transportation you can carry the cylin- der vacuum cleaner by the handle of the dust container.

WARNING:

Danger of injury! Switch off the appliance when not working with it and observe the notices under Zchapter 2.4, „Switching off“.

ATTENTION:

Take care that you don't accidentally press the dust container release catch when carry- ing the vacuum cleaner.

2.6When interrupting your work

To park the appliance or during work breaks, you can hang the parking hook into the parking hook holder (Fig. 9).

9

It is recommended to first retract the telescopic tube (Fig. 1/5).

ATTENTION:

Never store the appliance next to heat sources (e.g. stoves or radiators). Avoid exposing it to direct sunlight. Heat can dam- age the appliance.

10