Manuals / Runco / Computer Equipment / Computer Monitor

Runco CR-26HD, CR-32HDi manual Runco CL-810 Owner’s Operating Manual

Models: CR-26HD, CR-32HDi

1 68

Download 68 pages 21.6 Kb

Page 68

SERIAL NUMBER

RUMA-011090

rev 01-04-07 v2.4

Runco International • 2900 Faber Street • Union City, CA 94587 • Ph (510) 324-7777 / (800) 23RUNCO / Fax (510) 324-9300

www.runco.com

Runco CL-810 Owner’s Operating Manual

Image 68

Runco CR-26HD, CR-32HDi manual Runco CL-810 Owner’s Operating Manual

Contents

CR-26HD Page ONE Year Limited Warranty RIGHTS, Limits and Exclusions Runco INTERNATIONAL, INC Safety Precautions DOC Compliance NoticeTable of Contents Maintenance and Troubleshooting SpecificationsOperation Serial CommunicationsList of Figures List of Figures Introduction About This ManualUsing This Manual If you need Turn toDescription, Features and Benefits Key Features and BenefitsOptional Accessories Controls and Indicators Controls and FunctionsCrystal Series LCD Display at a Glance SpeakersInput 2 Audio Input Input 2 Composite Video Input Crystal Series LCD DisplayInputs and Outputs Input 3 Component Video RCA connectors DVI/Computer Input DigitalAudio Input RGB/DVI Atsc DTV InputCrystal Series LCD Display Remote Control Crystal Series LCD Display Remote ControlTimer OFF Button Memory Preset ButtonsOFF / on Numeric ButtonsAspect Ratio Selection Buttons ANA Anamorphic 4X3 StandardLetbox Letterbox Vwide VirtualWideSound Control Buttons Surrnd SurroundMTS/SAP Multichannel Television Sound/Second Audio Program Favorite Channel Selection ButtonsControls and Functions Battery Installation InstallationRemote Control Step Procedure For Details, refer to Quick SetupInstallation Overview Installation Considerations Wall-Mounting the Crystal Series LCD DisplayAmbient Light Other ConsiderationsConnections to the Crystal Series LCD Display Antenna/Cable TV ConnectionDVI Connections Refer to Computer/Video Signal Compatibility on page 56 for Analog RGB ConnectionsInput Connection InputLeft Side Connector Pin AssignmentsRS-232 Controller Installation Changing the OSD Language Turning on the PowerOperation Setting the PC Display Properties Using the On-Screen Menus Picture Adjust TimerSetup SourceMain Menu SourceAspect Ratio TV Input1 Input2 Input3Aspect Ratio Settings Remote Aspect Ratio Control Description KeyTypical Pluge Pattern for Adjusting Brightness Picture AdjustTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Audio Audio Balance Equalizer Surround Audio Language TV SpeakerTimer Channel Auto Tuning Add/Erase Favorite ChannelTimer On Timer Off Timer Sleep Timer Time Zone ChannelCharacteristics of the incoming signal SetupFCC Ratings and Content Categories Rating/Category DescriptionOffensive language ISF Calibration Picture Adjust White Balance Blue Enable Gamma Baud Rate Command Ack Factory Reset Splash DurationISF Calibration Menu should be used by ISF-certified technicians onlyWhite Balance Gain OffsetCrystal Series LCD Display Splash Screen Using Picture-In-Picture PIP Main Button on the remote controlAvailable Main and PIP Source Combinations Aspect Size Position PIP Swap Swap TV/AV Mode Swapping the Main PIP Images Button on the remote controlPIP Audio Programs Swap button on the remote control Broadcast Mode Receive Mode Mono Stereo Stereo Sound/SAPCompatibility with Stereo and SAP Audio Broadcasts Mono+SAPOperation Maintenance and Troubleshooting Troubleshooting TipsTroubleshooting Chart Symptom Possible Causes SolutionComputer/Video Signal RS-232 Connection and Port Configuration Serial Command SyntaxSerial Commands Command DescriptionSAB Key 0002 0043 Specifications Crystal Series LCD Display SpecificationsCrystal Series LCD Display Specifications Specifications are subject to change without noticeCrystal Series LCD Display Dimensions CR-26HD DimensionsCR-32HDi Dimensions Computer/Video Signal Compatibility Computer/Video Signal Compatibility ChartPage Runco CL-810 Owner’s Operating Manual