Manuals / Ryobi / Power Tools / Saw

Ryobi RTS31 manual Tools Needed, Blades, Framing Square Phillips Screwdriver Flathead

Models: RTS31

1 44

Download 44 pages 62.4 Kb

Page 12

Image 12

FEATURES

BLADES

For maximum performance, it is recommended that you use the 10 in. carbide-tipped combination blade provided with your saw. Additional blade styles of the same high quality are available for specific operations such as ripping. Your local dealer can provide you with complete information.

Blade kerf width must be within the limits stamped on the riving knife.

WARNING:

Do not use blades rated less than the speed of this tool. Failure to heed this warning could result in personal injury.

TOOLS NEEDED

The following tools (not included) are needed for assembly and making adjustments:

Framing Square

Phillips

Screwdriver

Flathead

Screwdriver

COMBINATION
SQUARE	ADJUSTABLE WRENCH
	ADJUSTABLE WRENCH

c-clamps hex key (3 mm)

Fig. 4

Page 12

Image 12

Ryobi RTS31 manual Tools Needed, Blades, Framing Square Phillips Screwdriver Flathead, Clamps hex key 3 mm

Contents

OPERATOR’S Manual Save this Manual for Future ReferenceTable of contents IntroductionGeneral Safety Rules Read ALL InstructionsSpecific Safety Rules  Never Start a Tool When ANY ROTATiNG COMPonent is in Contact with the Workpiece  Never Operate the SAW on the FloorSpecific Safety Rules Symbols Symbol Signal MeaningSpeed and Wiring ElectricalExtension Cords Electrical ConnectionGlossary of Terms Features Product SpecificationsKnow Your Table SAW See FigureSwitch assembly Switch KEY Switch in Locked PositionOperating Components To Turn Your SAW onTools Needed BladesFraming Square Phillips Screwdriver Flathead Clamps hex key 3 mmLoose Parts Following items are included with your table sawAssembly To attach the wheel assemblyUnpacking Mounting HolesTo install the Handle To attach the LegTo secure/level the saw To open/close set-up/tear down LEG StandSET-UP To open set-up the leg standTo Install miter Fence To move the LEG StandTo remove/replace the Throat Plate Throat PlateTo check SAW Blade installation To Change riving knife PositionsUnlocked LockedTo Install the ANTI-KICKBACK Pawls and Blade Guard See Figures 15Large WrenchVertical Adjustment To Check and Align the riving knife Saw BladeTo Store the table saw Accessories To store push stickSee Figures 20 Operation ApplicationsBasic Operation of the Table Saw Causes of KickbackHow to Make a jig for rip cutting narrow workpiece Cutting aidsAuxiliary Fence Push Sticks Push BlocksTypes of cuts Cutting TipsHOW to Make a Featherboard HOW to Mount a FeatherboardFeatherboard To Adjust the Bevel indicator To Change Blade DepthTo Change Blade Angle bevel To position the Sliding Miter TableTo Check Miter Base Parallelism See Figures 32To Adjust the Miter table To Check Miter Fence AlignmentEccentric Screw Nylock NUT To Set the rip fence Scale indicator to the Blade To use the Rip FenceSAW Rear LIPTo use Outfeed Support To use the table extensionTo extend To closeAdjusting Bolts Adjusting bolts 4 Heeling paralleling the bladeSee Figures 40 Framing SquareSwitch On Switch OFF Switch KEY Switch in Locked Position Making a cross cutSee Figures 42 Cross CUT Place Left Hand on WorkpieceMaking a RIP cut Making a miter cutRIP CUT Bladefence Scale Miter CUT Straight Making a bevel cross cut Making a bevel rip cutSee Figures 46 BevelMaking a compound bevel miter cut Adjusting Handwheel Making a Large Panel cutMaking a NON-THROUGH cut Large Panel CUT RIP FenceMaking a Dado cut NON-THROUGH CUT Blade Guard Removed Push Stick Dado CUTOnce all dado cuts are completed Adjustments To REPLACe the BladeSee Figures 53 Combination Adjustment Square Blade Bolt To SET the blade at 0See Figures 56 If the blade is not perfectly verticalTo adjust Quick-Stop To Check the Alignment of the RIP Fence to the BladeBlade Rip fence Screws Locking Lever Framing Square Maintenance AccessoriesGeneral Maintenance LubricationTroubleshooting Troubleshooting RTS31