Manuals / Samsung / Household Appliance / Air Conditioner

Samsung ASV18PSPNXEA, ASV13PSPNXEA, ASV18PSPXXEA Press the button Press the button to set the time

Models: ASV18PUQXXEA ASV10PUQNXEA ASV18PSPXXEA ASV10PUQXXEA ASV24PUQNXEA ASV18PUQNXEA ASV24PUQXXEA ASV13PSPXXEA ASV10PSPXXEA ASV13PSPNXEA ASV18PSPNXEA ASV24PSPNXEA ASV13PUQNXEA ASV10PSPNXEA ASV24PSPXXEA ASV13PUQXXEA

1 41

Download 41 pages 41.26 Kb

Page 14

Setting On timer

1. Press thebutton.



2.Press the button to set the time.

You can set the time in half hourly unit from 30 minutes ~ 3 hours and hour unit from 3 hours ~ 24 hours.

Operating hour can be set from minimum 30 minutes to maximum 24 hours.

3.Press the Set/Cancel button to active it on.

On timer indicator stops blinking and reserved time will be displayed for 3 seconds.

If you don’t press Set/Cancel button within 10 seconds after selecting the time the air indicator on the indoor unit.

Cancel Press the Set/Cancel button.

Additional options available in On timer mode

You can select from Auto/Cool/Dry/Fan/Heat.

You can adjust the fan speed in Cool/Fan/Heat mode.

You can adjust the temperature in Auto/Cool/Dry/Heat mode.

• Only the latest setting timer will be applied between the On	Timer
and

•After setting the timer, the set time will be displayed for 3 seconds before it disappears.

•If Timer function is used in Heating mode, Air conditioner work into former mode. (ASV** Series)

14

Image 14

Samsung ASV18PSPNXEA manual Press the button Press the button to set the time, Press the Set/Cancel button to active it on

Contents

Air Conditioner Contents Follow directions Safety precautionsImportant safety symbols and precautions Wall socketFor Using For Cleaning Checking before use Operation rangesMain parts Power buttonChecking the name of the parts DisplayChecking the remote controller Remote controller buttonsStoring the remote controller Remote controller displayBattery changing time Inserting the batteriesBasic function Button to adjust the temperature PressCirculate the air Using the Turbo functionPress the Air swing button on the remote controller Position you preferMode Press the Set/Cancel button to active it on Press the button Press the button to set the timeTimer 5 hours Using the Smart Saver functionTimer 1 hour From the moment you have set the timerUsing the Quiet function Opening the panel Cleaning the indoor unitCleaning the outdoor unit heat exchanger Heat exchangerSlide it down Cleaning the air conditionerClean the Air Dry the Ai lter in a ventilated areaMaintaining the air conditioner Periodical checksTroubleshooting Connection Outdoor unit Heat exchanger during Heat mode in winterIf may not be a General information Model Name Included Models RemarkPower supply line, fuse or circuit breaker Choosing the installation locationInstalling the unit Won’t be considered in-warranty and charged to end userOutdoor Unit ModelTop view Side view When installing more than 1 outdoor unit When the air outlet is towards the wall Accessories in the outdoor unit case AccessoriesAccessories in the indoor unit case Tools required for installation General Tools Fixing the installation plateOptional accessories Tools for test operationsFix the indoor unit Connecting the assembly cableConnecting the cable Extend the assembly cable if necessary Each wire is labeled with the corresponding terminal numberSmooth the cut edges Then pull it out through the appropriate holeUnscrew the caps at the end of each pipe Purging the indoor unitCutting or extending the pipe Connect the pipesApplying the following torque Correct InclinedCracked Outer DiameterDrain hose installation Changing direction of the drain hosePurging the connected pipes Excessive torque can be cause of gas leakageAdding Refrigerant 1975 Covered by the Kyoto ProtocolTo check for gas leaks on the indoor unit Performing the gas leak testsTo check for gas leaks on the outdoor unit Leak test with nitrogen before opening valvesPart without insulation on the end of the pipes Outdoor unit installed on the wall by rackFixing the outdoor unit in place Properly ModelPress the Mode button to select Cool or Heat mode Pump down procedure when removing the productPress the Power button and check the following Final Check and Trial OperationHow to connect your extended power cables Questions or COMMENTS?