Manuals / Samsung / Household Appliance / Air Conditioner

Samsung ASV18PUQXXEA, ASV13PSPNXEA, ASV18PSPXXEA manual Checking before use, Operation ranges

Models: ASV18PUQXXEA ASV10PUQNXEA ASV18PSPXXEA ASV10PUQXXEA ASV24PUQNXEA ASV18PUQNXEA ASV24PUQXXEA ASV13PSPXXEA ASV10PSPXXEA ASV13PSPNXEA ASV18PSPNXEA ASV24PSPNXEA ASV13PUQNXEA ASV10PSPNXEA ASV24PSPXXEA ASV13PUQXXEA

1 41

Download 41 pages 41.26 Kb

Page 6

Checking before use

Operation ranges

The table below indicates the temperature and humidity ranges the air conditioner can be operated within. Refer to the

	Mode	Indoor	Outdoor	Indoor	Remark
	Mode	temperature	temperature	humidity	Remark
		temperature	temperature	humidity
				Relative
	Cooling	16˚C~32˚C	16˚C~46˚C	humidity	ASV10/13/18/24P 
				80% or less
	Dry	18˚C~32˚C	16˚C~46˚C	-	ASV10/13/18/24P 
	Dry	18˚C~32˚C	16˚C~46˚C	-	ASV10/13/18/24P 

If the air conditioner operates in cooling mode for long period of time in high humidity area, dew may be formed.

Maintaining your air conditioner

Internal protections via the unit control system

This internal protection operates if an internal fault occurs in the air conditioner.

	Type	Description
	Against cold air

	De-ice cycle

	Protect compressor	The air conditioner does not start operating immediately to protect the compressor of the
	Protect compressor	outdoor unit after it has been started.
		outdoor unit after it has been started.

• If the heat pump is operating in Heat mode, De-ice cycle is actuated to remove frost from an outdoor unit that may have deposited at low temperatures.

6

Image 6

Samsung ASV18PUQXXEA, ASV13PSPNXEA, ASV18PSPXXEA, ASV18PUQNXEA, ASV10PUQNXEA manual Checking before use, Operation ranges

Contents

Air Conditioner Contents Follow directions Safety precautionsImportant safety symbols and precautions Wall socket For Using For Cleaning Checking before use Operation ranges Main parts Power buttonChecking the name of the parts Display Checking the remote controller Remote controller buttons Storing the remote controller Remote controller displayBattery changing time Inserting the batteries Basic function Button to adjust the temperature Press Circulate the air Using the Turbo functionPress the Air swing button on the remote controller Position you prefer Mode Press the Set/Cancel button to active it on Press the button Press the button to set the time Timer 5 hours Using the Smart Saver functionTimer 1 hour From the moment you have set the timer Using the Quiet function Opening the panel Cleaning the indoor unitCleaning the outdoor unit heat exchanger Heat exchanger Slide it down Cleaning the air conditionerClean the Air Dry the Ai lter in a ventilated area Maintaining the air conditioner Periodical checks Troubleshooting Outdoor unit Heat exchanger during Heat mode in winter If may not be aConnection General information Model Name Included Models Remark Power supply line, fuse or circuit breaker Choosing the installation locationInstalling the unit Won’t be considered in-warranty and charged to end user Outdoor Unit Model When installing more than 1 outdoor unit  When the air outlet is towards the wallTop view Side view Accessories Accessories in the indoor unit caseAccessories in the outdoor unit case Tools required for installation General Tools Fixing the installation plateOptional accessories Tools for test operations Connecting the assembly cable Connecting the cableFix the indoor unit Extend the assembly cable if necessary Each wire is labeled with the corresponding terminal number Smooth the cut edges Then pull it out through the appropriate hole Unscrew the caps at the end of each pipe Purging the indoor unitCutting or extending the pipe Connect the pipes Applying the following torque Correct InclinedCracked Outer Diameter Drain hose installation Changing direction of the drain hose Purging the connected pipes Excessive torque can be cause of gas leakage Adding Refrigerant 1975 Covered by the Kyoto Protocol To check for gas leaks on the indoor unit Performing the gas leak testsTo check for gas leaks on the outdoor unit Leak test with nitrogen before opening valves Part without insulation on the end of the pipes Outdoor unit installed on the wall by rackFixing the outdoor unit in place Properly Model Press the Mode button to select Cool or Heat mode Pump down procedure when removing the productPress the Power button and check the following Final Check and Trial Operation How to connect your extended power cables Questions or COMMENTS?