Samsung DVD-R4000EU manual Manual programming, To put the unit on recording standby

Timer recording (continued)

Manual programming

[RAM] [DVD-R]

Remote control only

You can set your own programming conditions (up to 16 programmes).

Preparation

≥Switch [DVD, TV] (15) to “DVD”.

≥Ensure that this unit’s clock is set correctly.

≥Insert a disc for recording (make sure there is enough room for the programme you are going to record plus a little extra).

1Press [PROG/CHECK] (13).

≥The Timer Programme List screen appears.

TIMER						Remain
RECORDING								1:58 SP
						1:19:00			16.7 TUE
	No.	Name	Date	Start	Stop	Mode	PDC		Disc
									space
	01	BBC 1	16/ 7 TUE	1:19	1:22	SP	OFF		OK
			New Timer Programme

SELECT

		Press ENTER to store
ENTER	RETURN	new programme.

A line that is ready for programming is highlighted.

2Press [ENTER] (10).

≥The Timer Programme Correction screen appears.

TIMER					Remain		1:58 SP
RECORDING
						1:55:00	16.7 TUE
	Name	Date	Start		Stop	Mode	PDC
	----	----------	--:-- --		--:-- -- SP		---
						Title
		Please set Channel.
SELECT				No.
			0	--	9
ENTER	RETURN

3Use [1] (10) to move through the items and change the items with [3, 4] (10).

≥The current settings are shown each time you press [1]

(10).

≥You may use the numeric buttons (4) to enter “Name”, “Date”, “Start” and “Stop”.

TIMER			Remain
RECORDING				1:58 SP
			1:19:00		16.7 TUE
Name	Date	Start	Stop Mode		PDC

BBC 1 16/ 7 TUE 1:00 2:00 SP OFF

Title

≥Name (Programme Position/TV Station Name)

≥Date

Current date>the day before one month later>

Daily (Sunday to Saturday)>Daily (Monday to Saturday)> Daily (Monday to Friday)>Weekly (Sundays)>...> Weekly (Saturdays)

≥Start (start time)/Stop (finish time)

The time increases or decreases in 30-minute increments if

you hold the button.

≥Mode (Recording mode) XP>SP>LP>EP>FR (page 26)

≥PDC

ON>OFF (jjj) (page 33)

≥Title

Select “Title” and press [ENTER] (10), then refer to page 37 for entering title.

4Press [ENTER] (10) when you have finished making changes.

≥To continue programming: Repeat steps 2, 3, and 4.

5Press [PROG/CHECK] (13) or [RETURN] (23).

To put the unit on recording standby

Press [, TIMER] (12).

Ensure “” lights on the unit’s display.

To change the timer recording programme

1)While the Timer Programme List Screen is being shown, use [3, 4] (10) to select the programme you want to change, and press [ENTER] (10) to show the Timer Programme Correction screen.

≥You may also select programme by inputting a 2-digit number using the numeric buttons (4).

≥Use [2, 1] (10) to move to the page preceding or following the one on display.

2)Move through the items with [1] (10) and change the settings with [3, 4] (10) and press [ENTER] (10).

Note

≥The built-in clock employs 24-hour system.

≥The remaining time is not shown if you insert discs other than DVD-RAM or DVD-R.

≥The remaining time displayed is calculated based on the current recording mode.

≥If the disc is protected (pages 38, 72), the unit switches to standby but does not go on standby for recording. Check the disc carefully.

≥Recording is not possible unless you set “Disc Protection” in “DISC INFORMATION” to “Off” (page 38).

≥You cannot record to a disc if the write protect tab on a cartridge disc is set to protect. Release this before operation (page 72).

≥Even if the unit is put in the timer recording standby mode or the timer recording is being performed, you can play a programme.

≥If the unit is not put in the timer recording standby mode at the latest 10 minutes before the programmed timer recording

starting time, the [] flashes on the unit display. In this case, press the [ , TIMER] (12) button to put the unit in the timer

recording standby mode.

≥When recording more than one programme in a row, for DVD- RAM the first few seconds, and for DVD-R about the first 30 seconds of all programmes from the second one onwards will not be recorded.

34