Samsung LE32MM8 manual Listening through a Receiver, Check Points before Requesting Service

View TV

Air 28

Listening through a Receiver

You can listen to sound through a receiver instead of the TV speaker.

1.Press the Anynet+ button.

Press the ▲ or ▼ button to select Receiver, then press the

ENTER/OK button.

2.	Press the ◄ or ► button to select to On, then press the	Select Device
		Record
	ENTER/OK button.
		Menu on Device
	Now you can listen to sound through the receiver.
		Device Operation
3.	Press the EXIT button to exit.
		Receiver	:On
➣ When the receiver is set to On, you can listen to the TV sound
		Setup
	through the 2-channel receiver.
		Move	Enter
➣ If the receiver is exclusively for a home theater only (supporting		Exit

audio only), it may not appear in the device list.













➣Only when you have connected the optical jack of the TV and the receiver properly, does Receiver work.

➣In case of a content with copyright problem, listening through the receiver may not properly operate.

➣When listening through the receiver, there are restrictions for using the PIP and audio-related menu.

Check Points before Requesting Service

Symptom	Solution
Anynet+ does not	■ Check if the device is an Anynet+ device. The Anynet+ system supports Anynet+
work.	devices only.
	■ Connect only one receiver.
	■ Check if the Anynet+ device power cord is properly connected.
	■ Check the Anynet+ device’s Video/Audio/HDMI cable connections.
	■ Check whether Anynet+ (HDMI-CEC) is set to On in the Anynet+ setup menu.
	■ Check whether the TV remote control is in TV mode.
	■ Check whether it is Anynet+ exclusive remote control.
	■ Anynet+ doesn’t work at a certain condition. (Searching channels)
	■ When connecting or removing the HDMI cable, please make sure to search
	devices again or restart your TV.
	■ Check if the Anynet+ Function of Anynet+ device is set on.
I want to start	■ Check if the Anynet+ device is properly connected to the TV and check if the
Anynet+.	Anynet+ (HDMI-CEC) is set to On in the Anynet+ Setup menu.
	■ Press the TV button on the TV remote control to switch to TV. Then press the
	Anynet+ button to show the Anynet+ menu and select a menu you want.

I want to exit Anynet+. ■ Select View TV in Anynet+ menu.

■Press the SOURCE button on the TV remote control and select a device other than Anynet+ devices.

■Press any of CH, CH LIST, PRE-CH, and such to change to the

TV mode. (Note that the channel button operates only when a tuner-embedded

Anynet+ device is not connected.)

The Connecting to	■ You cannot use the remote control when you are configuring Anynet+ or
Anynet+ device…	switching to a view mode.
message appears on	■ Use the remote control when the Anynet+ setting or switching to view mode is
the screen.	complete.
The Anynet+ device	You cannot use the play function when Plug & Play is in progress.
does not play.
The connected device	■ Check whether or not the device supports Anynet+ functions.
is not displayed.	■ Check whether or not the HDMI cable is properly connected.
	■ Check whether Anynet+ (HDMI-CEC) is set to On in the Anynet+ setup menu.
	■ Search Anynet+ devices again.
	■ You can connect an Anynet+ device using the HDMI cable only. Some HDMI
	cables may not support Anynet+ functions.
The TV program	Check whether the antenna jack on the recording device is properly connected.
cannot be recorded.
The TV sound is not
output through the	Connect the optical cable between TV and the receiver.
receiver.

English - 57