15.0 | Samsung M8 specification

SPECIFICATIONS

o

08.0

Recommended case temperature

measurement position

15.0

N

N

08.0

Recommended case temperature

measurement position

o

Figure 3-1:Measurement Position.

Spinpoint M8 Product Manual REV 2.3

11

Image 17

Samsung M8 manual 15.0

Contents

M8 Product Manual Page Table of Contents Servo System Read and Write Operations Read Fpdma Queued 60h Read Log Extended 2Fh Read Long 22h Table of Tables Manual Organization ScopeUser Definition Reference Sata Introduction Description Key Features Hardware Requirements Standards and Regulations Specification Summary SpecificationsSpecifications Spindle speed RPM RPM Class Logical Configurations Physical SpecificationsPhysical Specifications Physical dimensions Performance Specifications Power consumption Power consumptionPower Requirements Rated Environmental Specifications Environmental Specifications 15.0 Reliability Specifications Space Requirements Installation Mounting Unpacking Instructions Orientation Mounting Dimensions Mounting-Screw Clearance Clearance Sata Connectivity Cable ConnectorsVentilation Serial ATA Management Power HDD Power, Sata Interface, and Factory Jumper Connector Pin Locations on the Drive Pcba DC Power Connector and SATA-Bus Interface Cable Connections Drive Installation Base Casting Assembly Head / Disk Assembly HDADC Spindle Motor Assembly Disk Drive Operation CoverAssembly Head Stack Assembly Disk Stack AssemblyVoice Coil Motor and Actuator Latch Assemblies Air Filtration System Disk Controller Digital Signal Process and Interface ControllerDrive Electronics DDR Buffer Control Block Host Interface Control Block Frequency Synthesizer Disk Control BlockDisk Ldpc Control Block Read/Write IC Power ManagementTime Base Generator Automatic Gain Control Analog to Digital Converter ADC and FIR Analog Anti-Aliasing Low Pass Filter Read Channel Servo SystemRead and Write Operations Read Caching Firmware FeaturesWrite Channel Write Caching Automatic Defect Allocation Defect ManagementMulti-burst ECC Correction Smart Sata Terminology Sata II Interface Spinpoint M8 Product Manual REV Signal Descriptions Physical Interface Signal Summary 2 I/O Register Address When read When writtenControl Block Register Descriptions Registers Features Register and Feature Extended Register Ex F1h Command Block Register DescriptionsError Register Ex F1h Device Control Register ex F6h Device Register Ex F6h Command Register Ex F7h Status Register Ex F7h Device Activity Signal Sata II Feature SETStaggered Spin-up Disable Control Auto-Activate in DMA Setup FIS Phy. Event Counters Sata Power Management Software Settings Preservation Command Code Parameters ATA Command DescriptionsCommand Table Check Power Mode E5h Command Descriptions Device Configuration Overlay Feature Register Values Device Configuration Overlay B1hCommand Download Micro Code 92h Device Configuration Identify data structure Word Content Diagnostic Codes Execute Device Diagnostics 90hFlush Cache E7h, EAh extended Format Track 50h Identify Device information Content Description =the fields reported in word 88 are valid EXT =Media Card Pass Through command feature set supported WWN Word Content Description Idle Immediate E1h Automatic Standby Timer PeriodsIdle E3h NOP 00h Initialize Device Parameters 91hRead Buffer E4h Read DMA C8h, 25h extended Read Long 22h Read Multiple Command C4h, 29h extendedRead Log Extended 2Fh Read Verify Sectors 40h, 41h extended Read Native Max Address F8h, 27h extendedRead Sectors 20h, 24h extended Recalibrate 10h Security Disable Password F6hSecurity Erase Prepare F3h Security Erase Unit F4h Security Erase Unit Password Word Content Security Set Password F1hSecurity Set Password data content Security Freeze Lock F5h Identifier Level Command result Set Features EFhSecurity Unlock F2h Seek 7xh 12 Transfer Mode Values 11 Set Features Register Definitions 13 Set Max Feature Register Values Set Multiple Mode C6hSet Max Address F9h, 37h extended Sleep E6h Smart disable operations D9h 14 Smart Feature Registers ValuesSmart enable/disable attribute auto-save D2h Smart B0h Smart execute off-line immediate D4h Smart enable operations D8h 15 Device Smart Data Structure Smart read data D0h Data Structure Revision Number 16 Smart Attribute Status Flags Bit Name Description 18 Off-line Data Collection Status Values 17 Smart Attribute Data List 19 Self-test Execution Status Values Self-test execution status byte Smart write log sector D6h Smart read log sector D5hSmart return status DAh Write Buffer E8h Standby Immediate E0hWrite DMA CAh, 35h extended Write Fpdma Queued 61h Write Sectors 30h, 34h extended Write Multiple Command C5h, 39h extendedWrite Long 32h Spinpoint M8 Product Manual REV General Information MaintenanceMaintenance Precautions HDD handling guide -Please handle HDD by side surfaces HDD handling guide Prevent Shocks Service and Repair