Ext | Samsung M8 guide

	Word	Content			Description
			3	Device initiating interface power management enabled
			2	DMA Setup Auto-Activate optimization enabled
			1	Non-zero buffer offsets in DMA Setup FIS enabled
			0	Reserved (set to 0)
	80	01FFh	Major version number
	80	01FFh	15-0 ATA-1, ATA-2, ATA-3 and ATA/ATAPI-4, 5, 6, 7
			15-0 ATA-1, ATA-2, ATA-3 and ATA/ATAPI-4, 5, 6, 7
	81	0028h	Minor version number
	81	0028h	15-0	ATA/ATAPI-7 X3T13 1532D revision 0
			15-0	ATA/ATAPI-7 X3T13 1532D revision 0
			Command set supported.
			15	Obsolete
			14	1=NOP command supported
			13	1=READ BUFFER command supported
			12	1=WRITE BUFFER command supported
			11	Obsolete
			10	1=Host Protected Area feature set supported
			9	1=DEVICE RESET command supported
	82	746Bh	8	1=SERVICE interrupt supported
			7	1=Release interrupt supported
			6	1=	Look-ahead supported
			5	1=Write cache supported
			4	1=supports PACKET Command feature set
			3	1=Power Management feature set supported
			2	1=Removable Media feature set supported
			1	1=Security Mode feature set supported
			0	1=SMART feature set supported

Command sets supported.

15Shall be set to zero

14Shall be set to one

131=FLUSH CACHE Ext supported

121=Mandatory FLUSH CACHE command supported

111=Device Configuration Overlay features supported

101=48 bit address feature supported

9 1-Automatic Acoustic feature supported

83	7F69h	8	1=SET MAX Security feature supported
		7	1=Set Address Offset Reserved Area Boot, INCITS TR27:2001
		6	1=SET FEATURES subcommand required to spin-up after power-up.
		5	1=Power up standby feature set supported
		4	1=Removable media status notification feature set supported
		3	1=Advanced Power Management feature set supported
		2	1=CFA feature set supported
		1	1=READ/WRITE DMA QUEUED supported
		0	1=DOWNLOAD MICROCODE command supported

Command set/feature supported extension.

15Shall be set to 0

14Shall be set to 1

131=IDLE IMMEDIATE with UNLOAD FEATURE supported

12Reserved for technical report

11Reserved for technical report

101=URG bit supported for WRITE STREAM DMA EXT and WRITE STREAM

84

6123h

EXT

91=URG bit supported for READ STREAM DMA EXT and READ STREAM EXT

8 64-bit World wide name supported

7 1=Write DMA Queued FUA Ext command supported

61=Write DMA FUA Ext and Write Multiple FUA Ext command supported

51=General purpose logging feature set supported

41=Streaming feature set supported

Spinpoint M8 Product Manual REV 2.3

53

Image 59

Samsung M8 manual Ext

Contents

M8 Product Manual Page Table of Contents Servo System Read and Write Operations Read Fpdma Queued 60h Read Log Extended 2Fh Read Long 22h Table of Tables Manual Organization ScopeUser Definition Reference Sata Introduction Description Key Features Hardware Requirements Standards and Regulations Spindle speed RPM RPM Class SpecificationsSpecification Summary Specifications Physical dimensions Physical SpecificationsLogical Configurations Physical Specifications Performance Specifications Rated Power consumptionPower consumption Power Requirements Environmental Specifications Environmental Specifications 15.0 Reliability Specifications Space Requirements Installation Mounting Unpacking Instructions Orientation Mounting Dimensions Mounting-Screw Clearance Clearance Sata Connectivity Cable ConnectorsVentilation Serial ATA Management Power HDD Power, Sata Interface, and Factory Jumper Connector Pin Locations on the Drive Pcba DC Power Connector and SATA-Bus Interface Cable Connections Drive Installation Disk Drive Operation Head / Disk Assembly HDABase Casting Assembly DC Spindle Motor Assembly CoverAssembly Air Filtration System Disk Stack AssemblyHead Stack Assembly Voice Coil Motor and Actuator Latch Assemblies Disk Controller Digital Signal Process and Interface ControllerDrive Electronics DDR Buffer Control Block Host Interface Control Block Frequency Synthesizer Disk Control BlockDisk Ldpc Control Block Automatic Gain Control Power ManagementRead/Write IC Time Base Generator Analog to Digital Converter ADC and FIR Analog Anti-Aliasing Low Pass Filter Read Channel Servo SystemRead and Write Operations Read Caching Firmware FeaturesWrite Channel Write Caching Smart Defect ManagementAutomatic Defect Allocation Multi-burst ECC Correction Sata Terminology Sata II Interface Spinpoint M8 Product Manual REV Signal Descriptions Physical Interface Signal Summary Registers When read When written2 I/O Register Address Control Block Register Descriptions Device Control Register ex F6h Command Block Register DescriptionsFeatures Register and Feature Extended Register Ex F1h Error Register Ex F1h Device Register Ex F6h Command Register Ex F7h Status Register Ex F7h Auto-Activate in DMA Setup FIS Sata II Feature SETDevice Activity Signal Staggered Spin-up Disable Control Phy. Event Counters Sata Power Management Software Settings Preservation Command Code Parameters ATA Command DescriptionsCommand Table Check Power Mode E5h Command Descriptions Download Micro Code 92h Device Configuration Overlay B1hDevice Configuration Overlay Feature Register Values Command Device Configuration Identify data structure Word Content Format Track 50h Execute Device Diagnostics 90hDiagnostic Codes Flush Cache E7h, EAh extended Identify Device information Content Description =the fields reported in word 88 are valid EXT =Media Card Pass Through command feature set supported WWN Word Content Description Idle Immediate E1h Automatic Standby Timer PeriodsIdle E3h Read DMA C8h, 25h extended Initialize Device Parameters 91hNOP 00h Read Buffer E4h Read Long 22h Read Multiple Command C4h, 29h extendedRead Log Extended 2Fh Read Verify Sectors 40h, 41h extended Read Native Max Address F8h, 27h extendedRead Sectors 20h, 24h extended Security Erase Unit F4h Security Disable Password F6hRecalibrate 10h Security Erase Prepare F3h Security Freeze Lock F5h Security Set Password F1hSecurity Erase Unit Password Word Content Security Set Password data content Seek 7xh Set Features EFhIdentifier Level Command result Security Unlock F2h 12 Transfer Mode Values 11 Set Features Register Definitions Sleep E6h Set Multiple Mode C6h13 Set Max Feature Register Values Set Max Address F9h, 37h extended Smart B0h 14 Smart Feature Registers ValuesSmart disable operations D9h Smart enable/disable attribute auto-save D2h Smart execute off-line immediate D4h Smart enable operations D8h 15 Device Smart Data Structure Smart read data D0h Data Structure Revision Number 16 Smart Attribute Status Flags Bit Name Description 18 Off-line Data Collection Status Values 17 Smart Attribute Data List 19 Self-test Execution Status Values Self-test execution status byte Smart write log sector D6h Smart read log sector D5hSmart return status DAh Write Fpdma Queued 61h Standby Immediate E0hWrite Buffer E8h Write DMA CAh, 35h extended Write Sectors 30h, 34h extended Write Multiple Command C5h, 39h extendedWrite Long 32h Spinpoint M8 Product Manual REV General Information MaintenanceMaintenance Precautions HDD handling guide -Please handle HDD by side surfaces HDD handling guide Prevent Shocks Service and Repair