Mounting-Screw Clearance | Samsung M8 specification

INSTALLATION

4.3.2Clearance

The printed circuit board (PCB) is designed to be very close to the mounting holes. Do not exceed the specified length for the mounting screw described in Figure 4-3. The specified screw length allows full use of the mounting-hole threads, while avoiding damage or placing unwanted stress on the PCB.

Figure 4-3: Mounting-Screw Clearance

CAUTION: Using mounting screws that are longer than the maximum lengths specified in Figure 4-3 voids the warranty of the drive.

Spinpoint M8 Product Manual REV 2.3

16

Image 22

Samsung M8 manual Mounting-Screw Clearance

Contents

M8 Product Manual Page Table of Contents Servo System Read and Write Operations Read Fpdma Queued 60h Read Log Extended 2Fh Read Long 22h Table of Tables User Definition ScopeManual Organization Sata Reference Description Introduction Key Features Standards and Regulations Hardware Requirements Specifications SpecificationsSpecification Summary Spindle speed RPM RPM Class Physical Specifications Physical SpecificationsLogical Configurations Physical dimensions Performance Specifications Power Requirements Power consumptionPower consumption Rated Environmental Specifications Environmental Specifications 15.0 Reliability Specifications Installation Space Requirements Unpacking Instructions Mounting Mounting Dimensions Orientation Clearance Mounting-Screw Clearance Ventilation Cable ConnectorsSata Connectivity Serial ATA Power Management HDD Power, Sata Interface, and Factory Jumper Connector Pin Locations on the Drive Pcba Drive Installation DC Power Connector and SATA-Bus Interface Cable Connections DC Spindle Motor Assembly Head / Disk Assembly HDABase Casting Assembly Disk Drive Operation CoverAssembly Voice Coil Motor and Actuator Latch Assemblies Disk Stack AssemblyHead Stack Assembly Air Filtration System Drive Electronics Digital Signal Process and Interface ControllerDisk Controller DDR Host Interface Control Block Buffer Control Block Disk Ldpc Control Block Disk Control BlockFrequency Synthesizer Time Base Generator Power ManagementRead/Write IC Automatic Gain Control Analog Anti-Aliasing Low Pass Filter Analog to Digital Converter ADC and FIR Read and Write Operations Servo SystemRead Channel Write Channel Firmware FeaturesRead Caching Write Caching Multi-burst ECC Correction Defect ManagementAutomatic Defect Allocation Smart Sata II Interface Sata Terminology Spinpoint M8 Product Manual REV Physical Interface Signal Summary Signal Descriptions Control Block Register Descriptions When read When written2 I/O Register Address Registers Error Register Ex F1h Command Block Register DescriptionsFeatures Register and Feature Extended Register Ex F1h Device Control Register ex F6h Command Register Ex F7h Device Register Ex F6h Status Register Ex F7h Staggered Spin-up Disable Control Sata II Feature SETDevice Activity Signal Auto-Activate in DMA Setup FIS Phy. Event Counters Software Settings Preservation Sata Power Management Command Table ATA Command DescriptionsCommand Code Parameters Command Descriptions Check Power Mode E5h Command Device Configuration Overlay B1hDevice Configuration Overlay Feature Register Values Download Micro Code 92h Device Configuration Identify data structure Word Content Flush Cache E7h, EAh extended Execute Device Diagnostics 90hDiagnostic Codes Format Track 50h Content Description Identify Device information =the fields reported in word 88 are valid EXT =Media Card Pass Through command feature set supported Word Content Description WWN Idle E3h Automatic Standby Timer PeriodsIdle Immediate E1h Read Buffer E4h Initialize Device Parameters 91hNOP 00h Read DMA C8h, 25h extended Read Log Extended 2Fh Read Multiple Command C4h, 29h extendedRead Long 22h Read Sectors 20h, 24h extended Read Native Max Address F8h, 27h extendedRead Verify Sectors 40h, 41h extended Security Erase Prepare F3h Security Disable Password F6hRecalibrate 10h Security Erase Unit F4h Security Set Password data content Security Set Password F1hSecurity Erase Unit Password Word Content Security Freeze Lock F5h Security Unlock F2h Set Features EFhIdentifier Level Command result Seek 7xh 11 Set Features Register Definitions 12 Transfer Mode Values Set Max Address F9h, 37h extended Set Multiple Mode C6h13 Set Max Feature Register Values Sleep E6h Smart enable/disable attribute auto-save D2h 14 Smart Feature Registers ValuesSmart disable operations D9h Smart B0h Smart enable operations D8h Smart execute off-line immediate D4h Smart read data D0h 15 Device Smart Data Structure Data Structure Revision Number Bit Name Description 16 Smart Attribute Status Flags 17 Smart Attribute Data List 18 Off-line Data Collection Status Values Self-test execution status byte 19 Self-test Execution Status Values Smart return status DAh Smart read log sector D5hSmart write log sector D6h Write DMA CAh, 35h extended Standby Immediate E0hWrite Buffer E8h Write Fpdma Queued 61h Write Long 32h Write Multiple Command C5h, 39h extendedWrite Sectors 30h, 34h extended Spinpoint M8 Product Manual REV Maintenance Precautions MaintenanceGeneral Information HDD handling guide -Please handle HDD by side surfaces Service and Repair HDD handling guide Prevent Shocks