Installation, Space Requirements | Samsung M8 guide

INSTALLATION

CHAPTER 4 INSTALLATION

This chapter describes how to unpack, mount, configure and connect a Spinpoint M8 hard disk drive. It also describes how to install the drive in systems.

4.1Space Requirements

Figure 4-1 shows the external dimensions of the drive.

Figure 4-1: Mechanical Dimension

Spinpoint M8 Product Manual REV 2.3

13

Image 19

Samsung M8 manual Installation, Space Requirements

Contents

M8 Product Manual Page Table of Contents Servo System Read and Write Operations Read Fpdma Queued 60h Read Log Extended 2Fh Read Long 22h Table of Tables User Definition ScopeManual Organization Reference Sata Introduction Description Key Features Hardware Requirements Standards and Regulations Spindle speed RPM RPM Class SpecificationsSpecification Summary Specifications Physical dimensions Physical SpecificationsLogical Configurations Physical Specifications Performance Specifications Rated Power consumptionPower consumption Power Requirements Environmental Specifications Environmental Specifications 15.0 Reliability Specifications Space Requirements Installation Mounting Unpacking Instructions Orientation Mounting Dimensions Mounting-Screw Clearance Clearance Ventilation Cable ConnectorsSata Connectivity Serial ATA Management Power HDD Power, Sata Interface, and Factory Jumper Connector Pin Locations on the Drive Pcba DC Power Connector and SATA-Bus Interface Cable Connections Drive Installation Disk Drive Operation Head / Disk Assembly HDABase Casting Assembly DC Spindle Motor Assembly CoverAssembly Air Filtration System Disk Stack AssemblyHead Stack Assembly Voice Coil Motor and Actuator Latch Assemblies Drive Electronics Digital Signal Process and Interface ControllerDisk Controller DDR Buffer Control Block Host Interface Control Block Disk Ldpc Control Block Disk Control BlockFrequency Synthesizer Automatic Gain Control Power ManagementRead/Write IC Time Base Generator Analog to Digital Converter ADC and FIR Analog Anti-Aliasing Low Pass Filter Read and Write Operations Servo SystemRead Channel Write Channel Firmware FeaturesRead Caching Write Caching Smart Defect ManagementAutomatic Defect Allocation Multi-burst ECC Correction Sata Terminology Sata II Interface Spinpoint M8 Product Manual REV Signal Descriptions Physical Interface Signal Summary Registers When read When written2 I/O Register Address Control Block Register Descriptions Device Control Register ex F6h Command Block Register DescriptionsFeatures Register and Feature Extended Register Ex F1h Error Register Ex F1h Device Register Ex F6h Command Register Ex F7h Status Register Ex F7h Auto-Activate in DMA Setup FIS Sata II Feature SETDevice Activity Signal Staggered Spin-up Disable Control Phy. Event Counters Sata Power Management Software Settings Preservation Command Table ATA Command DescriptionsCommand Code Parameters Check Power Mode E5h Command Descriptions Download Micro Code 92h Device Configuration Overlay B1hDevice Configuration Overlay Feature Register Values Command Device Configuration Identify data structure Word Content Format Track 50h Execute Device Diagnostics 90hDiagnostic Codes Flush Cache E7h, EAh extended Identify Device information Content Description =the fields reported in word 88 are valid EXT =Media Card Pass Through command feature set supported WWN Word Content Description Idle E3h Automatic Standby Timer PeriodsIdle Immediate E1h Read DMA C8h, 25h extended Initialize Device Parameters 91hNOP 00h Read Buffer E4h Read Log Extended 2Fh Read Multiple Command C4h, 29h extendedRead Long 22h Read Sectors 20h, 24h extended Read Native Max Address F8h, 27h extendedRead Verify Sectors 40h, 41h extended Security Erase Unit F4h Security Disable Password F6hRecalibrate 10h Security Erase Prepare F3h Security Freeze Lock F5h Security Set Password F1hSecurity Erase Unit Password Word Content Security Set Password data content Seek 7xh Set Features EFhIdentifier Level Command result Security Unlock F2h 12 Transfer Mode Values 11 Set Features Register Definitions Sleep E6h Set Multiple Mode C6h13 Set Max Feature Register Values Set Max Address F9h, 37h extended Smart B0h 14 Smart Feature Registers ValuesSmart disable operations D9h Smart enable/disable attribute auto-save D2h Smart execute off-line immediate D4h Smart enable operations D8h 15 Device Smart Data Structure Smart read data D0h Data Structure Revision Number 16 Smart Attribute Status Flags Bit Name Description 18 Off-line Data Collection Status Values 17 Smart Attribute Data List 19 Self-test Execution Status Values Self-test execution status byte Smart return status DAh Smart read log sector D5hSmart write log sector D6h Write Fpdma Queued 61h Standby Immediate E0hWrite Buffer E8h Write DMA CAh, 35h extended Write Long 32h Write Multiple Command C5h, 39h extendedWrite Sectors 30h, 34h extended Spinpoint M8 Product Manual REV Maintenance Precautions MaintenanceGeneral Information HDD handling guide -Please handle HDD by side surfaces HDD handling guide Prevent Shocks Service and Repair