Unpacking Instructions, Mounting | Samsung 3.5 hard disk drives

INSTALLATION

4.2Unpacking Instructions

(1)Open the shipping container of the SpinPoint V40.

(2)Lift the packing assembly that contains the drive out of the shipping container.

(3)Remove the drive from the packing assembly. When you are ready to install the drive, remove it from the ESD (Electro Static Discharge) protection bag. Take precautions to protect the drive from ESD damage after removing it from the bag.

CAUTION: During shipment and handling, the anti-static ESD protection bag prevents electronic component damage due to electrostatic discharge. To avoid accidental damage to the drive, do not use a sharp instrument to open the ESD protection bag.

(4) Save the packing material for possible future use.

4.3Mounting

Refer to your system manual for complete mounting details.

(1)Be sure that the system power is off.

(2)For mounting, use four 6-32 UNC screws.

CAUTION: To avoid stripping the mounting-hole threads, the maximum torque applied to the screws must not exceed 8.0 Kg-cm (6.95 inch-pounds).

4.3.1 Orientation

Figure 4-2 shows the physical dimensions and mounting holes located on each side of the drive. The mounting holes on SpinPoint V40 hard disk drives allow the drives to be mounted in any direction.

SpinPoint V40 Product Manual

13

Image 21

Samsung 3.5 hard disk drives, spinpoint v40 manual Unpacking Instructions, Mounting, Orientation

Contents

Spinpoint SpinPoint V40 Product Manual Table of Contents Ervo S Ystem EAD and W Rite O Perations Irmware F EaturesSmart Programming Requirements Protocol OverviewTiming Service and Repair Maintenance Precautions107 General Information Table of Figures Page User Definition Manual OrganizationScope Terminology and Conventions Commands and MessagesComputer Message Format C/S Reference Key Features IntroductionDescription Hardware Requirements Standards and Regulations Specifications Specification Summary Logical Configurations Physical Specifications Performance Specifications 28.71 Power Requirements SV6003H SV6014H SV8004H Environmental Specifications Mtbf POH Reliability Specifications Space Requirements Installation Unpacking Instructions MountingOrientation 2Mounting Dimensions in Millimeters 3Mounting-Screw Clearance Clearance DC Power Connector Cable ConnectorsAT-Bus Interface Connector Ventilation SpinPoint V40 Product Manual Jumper Block Configurations Options for Jumper Block Configuration 7DC Power Connector and AT-Bus Interface Cable Connections Drive Installation Parameter System Startup Procedure System Setup Base Casting Assembly Head / Disk Assembly HDADC Spindle Motor Assembly Disk Drive Operation Exploded Mechanical View Head Stack Assembly Disk Stack AssemblyVoice Coil Motor and Actuator Latch Assemblies Air Filtration System Digital Signal Process and Interface Controller Drive ElectronicsAT Disk Controller 2SID2001 AT Controller Block Diagram Host Interface Control Block Disk Control Block Buffer Control Block SpinPoint V40 Product Manual Read/Write IC Power ManagementDisk ECC Control Block Frequency Synthesizer Automatic Gain Control Time Base GeneratorAsymmetry Correction Circuitry ASC Analog Anti-Aliasing Low Pass Filter 3Read/Write 88C5200 Servo System Read and Write OperationsRead Channel Firmware Features Write ChannelRead Caching Write Caching Automatic Defect Allocation Defect ManagementMulti-burst ECC Correction Smart Blank Signal Conventions Signal SummaryPhysical Interface Signal Descriptions Dmarq DMA Request DMACK- DMA AcknowledgeIntrq Drive Interrupt IOCS16- Drive 16-bit I/O PDIAG- Passed Diagnostics RESET- Drive ResetIordy I/O Channel Ready SD4 SD8 SD6 SD9 SD5SD3 SD2 Drive Host Drive DIR General Logical InterfaceBit Conventions Environment SpinPoint V40 Product Manual 2 I/O Register Address Command Block RegistersControl Block Registers N N N A a a Alternate Status Register 3F6h Control Block Register DescriptionsDrive Address Register 3F7h Device Control Register 3F6h Features Register 1F1h Command Block Register DescriptionsError Register 1F1h Data Register 1F0h Sector Count Register 1F2h Command Register 1F7hCylinder High Register 1F5h Cylinder Low Register 1F4h BSY Drdy DWF DSC DRQ Corr IDX ERR Status Register 1F7h At Command Register Descriptions Command Parameter Used SpinPoint V40 Product Manual Check Power Mode 98h, E5h Execute Device Diagnostics 90hDownload Micro Code 92h Flush Cache E7h Format Track 50hIdentify Device ECh Xxxx Word Content Description Capabilities Command set supported 95-128 0000h Reserved 129-159 Vendor specific 160-255 Idle 97h,E3h Idle Immediate 95h,E1hInitialize Device Parameters 91h Read Long 22hwith retry, 23h without retry Read Buffer E4h Read Multiple Command C4h Read Sectors 20hwith retry, 21hwithout retry Read Native Max Address F8h Read Verify Sectors 40hwith retry, 41hwithout retry Recalibrate 1xhSeek 7xh Mode Set Features EFh LBA InputsNormal outputs BSY Drdy DRQ ERR Description Sleep 99h, E6h Set Multiple Mode C6h Smart disable operation D9h Standby 96h,E2hSmart B0h Smart enable/disable attribute autosave D2h Smart enable operations D8hSmart execute off-line immediate D4h Byte Descriptions Smart read data D0h Off-line data collection capability Value Definition Smart read log sector D5h Smart capabilitySmart return status DAh Smart save attribution value D3h Standby Immediate 94h, E0h Standby 96h, E2hWrite Buffer E8h Write DMA CAh Write Sectors 30hwith retry, 31hwithout retry Write Multiple Command C5h SpinPoint V40 Product Manual Reset Response Error PostingProgramming Requirements BBK Command Error Register Status Register Sleep mode Power ConditionsStandby mode Idle mode Normal mode Protocol Overview PIO Data in Commands PIO Data Out Commands PIO Read CommandPIO Read Aborted Command PIO Write Aborted Command PIO Write CommandBSY=0 DRDY=1 BSY=1 BSY=0 DRQ=1 BSY=1 DRQ=0 Non-Data Commands DMA Data Transfer Commands Aborted DMA Command Initialize DMA Reset DMA Status BSY=0 BSY=1BSY=1 BSY=0 Register transfers Timing DIOR-/DIOW Write PIO data transfers PIO timing parameters Mode Addr valid See note T1 t2 DIOR-/DIOW DIOR-/DIOW Multiword DMA data transfer Multiword DMA timing parameters Mode Initiating an Ultra DMA data in burst Ultra DMA data transfer 19Ultra DMA data burst timing requirements Ultra DMA data burst timing requirements 5Sustained Ultra DMA data in burst Sustained Ultra DMA data in burst 6Host pausing an Ultra DMA data in burst Host pausing an Ultra DMA data in burst 7Device terminating an Ultra DMA data in burst 100 Device terminating an Ultra DMA data in burst 8Host terminating an Ultra DMA data in burst Host terminating an Ultra DMA data in burst 9Initiating an Ultra DMA data out burst 102 Initiating an Ultra DMA data out burst 10Sustained Ultra DMA data out burst Sustained Ultra DMA data out burst 11Device pausing an Ultra DMA data out burst 104 Device pausing an Ultra DMA data out burst 12Host terminating an Ultra DMA data out burst Host terminating an Ultra DMA data out burst 13Device terminating an Ultra DMA data out burst 106 Device terminating an Ultra DMA data out burst Maintenance Precautions Service And RepairGeneral Information