FEATURES (Continued)
Handsfree speaker
Your telephone is equipped with a handsfree speaker in the handset. Press the | to dial or receive | |
a call via speaker. Press | to deactivate the speaker and return to earpiece. |
|
NOTE: Do not lie the handset down on a surface when using handsfree as it will reduce the performance.
Headset (not included)
A headset can be connected to the telephone using the jack on the left of the handset. When a headset is connected, the microphone and earpiece of the handset will be disconnected. Also the handsfree speakerphone function is disabled.
NOTE: The earpiece volume may be high when using a headset. It may be necessary to adjust the volume when connecting the headset.
Mute
You can temporarily turn off the microphone so the person you are talking with cannot hear you.
1.Press MUTE button during a call. The display will show MUTE.
2.Press MUTE button again to take phone off mute.
Keylock
Press and hold the | button for 2 seconds will lock the keypad to prevent unintentional use. |
The LCD display will show "KEY LOCKED" when it is activated. | |
Press and hold the | for 2 seconds to release the keylock. |
NOTE: When the keylock is active and there is an incoming call, intercom from another handset ,
you can press 
to answer.
To adjust the volume
The handset receiver volume has 6 levels. Default is level 3. Speaker volume has 6 levels. Default is 4.
Press the 
key to adjust the handset receiver or speaker volume during a call.
NOTE: If the handset receiver or speaker volume is already at the maximum or minimum level,
pressing the 
or 
key will not change the volume level.
Page/handset locator PAGE
If you misplace the handset or want to page the person carrying the handset, press PAGE on the base station and the handset(s) will play music for approximately 60 seconds. The display will show "PAGING".
Press any key on the handset or press PAGE button on the base to stop the music.
FEATURES (Continued)
Intercom/Call transfer INT (for CLT-D6222, CLT-D6223 multi-handsets)
For
Intercom
1.Press INT in standby mode.
2.Input the handset number
3. | The receiving handset will play the PAGE music. Press | or | to answer the call. | ||
4. | Press | on either handset to end the INTERCOM. |
|
| |
NOTE: |
|
|
|
| |
| If the handset you are paging is busy or out of range, an error tone will sound. | ||||
| To stop calling another handset, press INT or | . |
|
| |
| During intercom, if there is incoming call, you will hear a long beep from the receiver. Press | ||||
| or | in either handset to answer the call. |
|
|
|
If you page the other handset and the other handset does not answer within one minute, the operation will stop and go back to standby mode.
Call transfer
1.During a call, press INT .
2.Input the handset number
The call will be put on hold and the other handset will play the PAGE music.
To cancel the transfer, press INT on the initial handset. The initial handset will return to the caller.
3.To answer the page, press 
or 
on the handset being paged. Or simply pick up the handset from the cradle if the AUTO TALK is set to ON.
4.Press
on the initial handset to transfer the call.
Or
1.During a call, press INT .
2.Input the handset number
The call will be put on hold and the other handset will play the PAGE music.
If you don't want to wait for the other handset to answer, press 
.
3. On the receiving handset, to accept the transfer and talk to the outside caller, press | or | . |
Or simply pick up the handset from the cradle if the AUTO TALK is set to ON. |
|
|
NOTE:
If the handset being paged does not answer the call within 30 seconds, it will page back the
initial handset. Press 
or 
on the initial handset to resume the conversation with the outside call. However, if the initial handset is paged back and does not answer within 30 seconds, the line will be cut and the telephone will be back to standby mode.
If the initial handset cannot reach the other handset, (for example, out of range or low battery) the initial handset will resume to the line after 30 seconds.
19 | 20 | ||
|
|
|
|
|
|
|
|
