Sanyo MPX-CD162, MPX-MD162 COMMAND TABLE (TABLE 4)

INTERFACE SPECIFICATIONS

COMMAND TABLE (TABLE 4)

The commands available are indicated in the table.

If a function is not available on the unit, the command will not operate even if sent.

LIVE

FULL 1

VCR PB

FULL 2

VERSION

(MULTI)

FULL 3

QUAD

FULL 4

PLUS

FULL 5

ZOOM

FULL 6

–

EXIT

STILL

FULL 7

SEQ.

FULL 8

MON 2

FULL 9

SECURITY LOCK ON

FULL 10

ACK

SECURITY LOCK OFF

FULL 11

NAK

FULL 12

GROUP SET*

FULL 13

GROUP CHECK*

FULL 14

GROUP CLEAR*

FULL 15

FULL 16

CLK. ADJ.

MENU RESET

ALARM STATUS SENSE

ON**

STATUS SENSE

OFF**

RS485

TRANSMISSION

START*

RS485 RCV

CHECK*

ALARM*

* Only RS485 ** Only RS232C

English

Contents

English GB Français F Español E About this manual À propos de ce manuel WARNING: CAUTION: REMOTE CONTROLLER CIRCUIT ACTIVE RECORDING AND VIDEO LOSS SETTING EACH CAMERA DISPLAY POSITION About the cooling fan REAR PANEL BASIC CONNECTIONS CONNECTIONS TO THE S-VIDEOTERMINALS [A] RS485 (RJ-11)terminal connection [B] Using the push-lockterminals [C] SENSOR ALARM OUT terminals REMOTE CONTROLLER CIRCUIT CONNECTIONS Live Picture Mode (see page 10) VCR Playback Mode (see page 18) Menu Mode Camera Live Picture Mode Lock VCR Playback Mode Lock Canceling the Security Lock Battery Life Replacing the Battery Press the LIVE button Live picture mode operations steps on monitor Live picture mode operations steps on monitor 2 (see page 17) Live picture mode Press a SELECT (1-16)button Example: To freeze the image from camera Example: To zoom in the image from camera Example: To zoom in the image from camera 4 and set the zoom range Example: To freeze the zoomed in image from camera Automatic sequential full screen display Switching the 4 divisions split screen Automatic sequential 4 divisions split screen display Switching between 16 divisions and 9 divisions split screen display Press the PLUS button Switching between 13 divisions and 6 divisions plus split screen display Example: To display the image from camera 12 in the plus screen area Automatic sequential plus display Example: To display the recorded image from camera 2 in the plus screen area Automatic sequential plus display of recorded pictures TO DISPLAY ON MONITOR 2 THE SAME IMAGE AS ON MONITOR Press the VCR button VCR playback mode operations steps on monitor VCR playback mode operations steps on monitor 2 (see page 17) VCR playback mode Example: To freeze the recorded image from camera Example: To zoom in the recorded image from camera Example: To zoom in the recorded image from camera 4 and set the zoom range Example: To freeze the zoomed in recorded image from camera Page Example: To display the recorded image from camera 12 in the plus screen area Page MENUS DISPLAYS Setting the language (CLOCK SET) (TIMER SET) 2-2~5 TO MAKE CHANGES TO THE SETTINGS Setting the VCR Output VCR SET menu VCR MODE REC SPEED ALARM REC SPEED SERIAL SET menu DATA SPEED ALARM SEND Unit address confirmation Setting the RS232C/RS485 communication BUZZER Changing the Settings MON.1 OUT ALARM SET menu RETRIGGER Setting the SENSOR SET Mode SENSOR SET menu SENSOR ALARM Setting the ACTIVE REC Recording Mode Setting the Video Loss Mode ACTIVE REC SET menu EXT ALARM REC SENSOR REC ACTIVE REC Settings Examples Example 1: Recording on the tape when an alarm trigger is received from camera Setting the Monitor Display MON2 SEQ.MODE MON2 MON1 MON.MASK LIVE Setting the camera title Setting up programmed recording for each camera CAMERA SET menu PROGRAM REC Setting the alarm duration for each camera AL. DURATION Setting the monitor masking for each camera MON. MASK Setting the sequential display interval for each camera SEQUENCE Setting the video loss operation mode Setting the video sensor area position, sensitivity level and response mode Changing a camera position VCR PB CLOCK Setting the clock and title display VCR PB TITLE DISPLAY SET menu LIVE CLOCK Displaying the Alarm Data LIVE PICTURES MODE ALARM Example: Resetting the Alarm RECORDED PICTURES MODE ALARM Alarms recorded on tape External Alarms DATA FORMAT TRANSMISSION PROTOCOL Transmission line: 2 conductors Transmission system: Half duplex SW No RS-232Cexclusive use RS-485exclusive use COMMANDS AVAILABLE FROM THE COMPUTER INFORMATION GATHERING COMMANDS STATUS SENSE(D7) STATUS SENSE(D7) byte assignment (Table 1) ALARM STATUS SENSE(D5) ALARM STATUS SENSE(D5) byte assignment (Table 2) COMMANDS AVAILABLE FROM THE MULTIPLEXER ACK(0A) NAK(0B) COMMAND TABLE (TABLE 4) Page SANYO INDUSTRIAL MULTIPLEXER WARRANTY OBLIGATIONS CUSTOMER INFORMATION Weekdays 8:30 AM – 5:00 PM Pacific Time