Manuals / Sanyo / Computer Equipment / Projector

Sanyo owner manual Image adjustment, Input source, Controlling the Projector, Description

Models: Projector

1 62

Download 62 pages 56.47 Kb

Page 36

Image adjustment

Chapter 4 Controlling the Projector

Image adjustment

This function is to adjust the projected picture image and save the image mode. To store the adjusted value, click Store button, and to load the adjusted value, click Load button.

Item	Description
Contrast		Adjusts picture contrast.
Brightness		(0~ 63)
Brightness		Adjusts picture brightness.
Color		(0~ 63)
Color		Adjusts picture color satura-
Tint		tion. (0~ 63)
Tint		Adjusts picture hue. (0~ 63)
Color temp		Sets a color temperature
		mode. (X Low, Low, Mid, High,
White balance		Adj.)
White balance
Red, Green, Blue		Adjusts each white balance
		respectively. (0~ 63)

*When changing the value of the white balance, the color temp. indicates "Adj."

Offset

Red, Green, Blue	Adjusts each offset respec-
Auto picture control	tively. (0~ 63)
Auto picture control	Sets auto picture control
Advanced color	level. (OFF, L1, L2)
Advanced color	Applies improved color
	adjustment with yellow
Sharpness	light controller. (Auto, OFF)
Sharpness	Adjusts picture sharpness.
Gamma	(0~ 31)
Gamma	Adjusts brightness of darker
Noise reduction	part of the picture. (0~ 15)
Noise reduction	Switches noise reduction mode (ON, OFF)
Progressive	Switches progressive mode (OFF, ON, Film)
Reset	Resets the Image adjustment to previous levels.
Store	Stores the Image adjustment values. Select an item [Image1 - Image10] from
	the pull-down menu and click Store button.

Load Image mode...........Loads the Image mode. Select an image mode from the pull-down menu

and click Load button. There may not be available mode depending on the input mode as shown in the table left.

36

Input source

Image mode Video Computer

Standard	4	4
Cinema	4	*
Real	*	4
Dynamic	4	4
Image1 - 10	4	4

*When Edge blending is set to "ON", Auto picture control and Advanced color are disable.

*When Color matching is set to "ON", Auto picture control, Advanced color, Color temp., White balance and Offset are disable.

✐The mark "4" means that the available image mode in the selected input source. The error message appears when selecting the disabled image mode indicated with "*".

Image 36

Sanyo owner manual Image adjustment, Input source, Controlling the Projector, Description, Image mode Video Computer

Contents

Wired Setting Projector Set-up and Operation Network Set-up and OperationCompliance Federal Communications Commission Notice Safety instructions CAUTION IN USING THE PROJECTOR VIA NETWORKSCAUTION IN USING NETWORK FUNCTION Table of contents Chapter 2 Setup ProceduresChapter 3 Basic Setting and Operation Chapter 4 Controlling the ProjectorChapter PreparationENGLISH Features Web Management function +p.31E-Mail Alert function +p.25 Network specifications of the projector Required operating environment for computersDisplay settings FeaturesExpression/Abbreviation Use of this manualTrademarks Cabling Between the Projector and a Hub or computer*1Flow of installation STEP 1 Connect the LAN and set the configurationSTEP 2 Network Configuration has completed Chapter 1 Preparation Setup Procedures Describes how to configure the networkChapter ENGLISHConnecting to the LAN line Network configurationSetting Procedure Description Network PIN code Network informationNetwork factory default Wired LAN factory default settingsChapter 2 Setup Procedures Chapter Basic Setting and Operation ENGLISHLogin the setting page of the projector 2 Login1 Enter the IP address Chapter 3 Basic Setting and Operation3 Display of main setting page Main setting page in the displayHow to use the setting page Example of the setting pageTypes of setting Text box setting Pull-down menu settingRadio button setting Check box settingHow to use the setting page ENGLISHInitial setting Chapter 3 Basic Setting and OperationDescription Network PIN code setting PJLink and password settingWhats PJLink? PJLink NoticeNetwork configuration Chapter 3 Basic Setting and OperationDescription E-mail setting E-mail settingmenu and follow the below steps ENGLISH1 Setting SMTP server and administrator address 3 Setting SMTP authentication2 Registering and deleting E-mail addresses Enter the e-mail address onto Add e-mail address and click Set button4 Setting POP server Error message for sending alert mail5 Option selection for sending alert mail ENGLISHExamples Type and contents of alert mail When internal PJ temperature is too highWhen PJ needs service When PJ lamp replacement time is reachedSNMP setting Trap option setting Check and delete the trap addressChapter 3 Basic Setting and Operation Checking the registered trap address and deleting the addressChapter Controlling the Projector ENGLISHPower control and status check About projector condition Power management is operatingThe temperature of the projector became too high ENGLISHControl InputSystem Available selection at the RGBPC analog inputAvailable selection at the RGBPC digital/RGBAV HDCP/HDMI input Available selection at the Video/S-video/Scart inputImage adjustment Input sourceChapter 4 Controlling the Projector DescriptionPC adjustment PC adjustmentENGLISH DescriptionSetting up the projector Screen settingLens adjustment Setting up the projectorENGLISH Item DescriptionSetting Chapter 4 Controlling the ProjectorDescription Countdown offSetting Setting up the projectorENGLISH Item DescriptionSetting Chapter 4 Controlling the ProjectorItem Description Edge blending.........Sets the seamless overlapping forSetting Setting up the projectorENGLISH DescriptionInformation InformationChapter 4 Controlling the Projector ItemsNetwork InformationENGLISH DescriptionIndication of the lamp status Indication of the filter statusChapter 4 Controlling the Projector StatusChapter AppendixConnection examples Use of telnet Web browser setting Q & A ENGLISHExamples of connection Peer-To-Peer connectionChapter 5 Appendix STP cross cableThe gateway Router installed in the network Network GroupNetwork Group ENGLISHUse of telnet ControlWhen the word Hello is replied, login has been succeeded Web browser setting Active Script/JavaScript enableProxy setting ActiveScript setting Examples OS/BrowsersWindows XP Professional Internet ExplorerProxy setting Using proxy serverNot using proxy server JavaScript Setting Netscape NavigatorProxy setting Using proxy serverJavaScript enable setting 2 Select Advanced icon and then click Proxies Change SettingsMAC OS SafariInstallation/Access Q Why doesn’t the setting page appear in my web browser?Q How can I restrict access from the computer Q How can I install several projectors? Password/LoginQ What should I do when I forget the IP address of the projector? Q What should I do when I forget the password Network PIN code?Q Why am I not receiving E-mail alert messages? OperationQ Can I control the projector by using the telnet application? Q What is the MAC address assigned to the projector?Others Q What are the rules for IP address assignment?Q Can I update the firmware of the projector Version of the firmwareNETWORK OWNERS MANUAL SO-KL8A