Sanyo MCO-19AIC, UV Setting the upper limit alarm temperature

115 24

㩷

㩷

Setting the upper limit alarm temperature

㩷

An upper limit temperature alarm is provided with the Incubator. The alarm temperature can be changed

by using the following procedure.

㩷

1. In the Stand-by Setting Display, turn the upper limit regulator on the control panel using a small

screwdriver to set the desired upper limit alarm temperature. The upper limit temperature can be set

between 34 and 52oC.

㩷

㩷

㩷

㩷

㩷

㩷

㩷

㩷

㩷

㩷

㩷

Note:

䊶Set the upper limit alarm temperature (High Limit) to at least 5oC higher than the chamber set

temperature.

䊶Set the upper limit alarm temperature to at least 50oC when H2O2 decontamination is performed.

2. After setting the parameter, press the MENU Key to display the menu, select OK, and press the

ENTER Key. The alarm temperature will be saved.

Refer to the tables of alarms and safety functions on page 46 for details.

Note:

䊶The alarm temperature will be changed at any time by turning the upper limit regulator even if the

Stand-by Setting Display is not displayed.

䊶Set the upper limit alarm temperature after the chamber reaches the set temperature for operation.

㩷

㩷

㩷

1 S t a n d - by S e t t ing

2 T e m p e r a t u r e 3 7 . 0 oC ( 0 . 0oC- 50 . 0 o C )

3 C O 2 D e n s i t y 5 . 0 % (0.0% - 20. 0 % )

4

5 K e y L o ck 0

( 0 . U n l o c k 1 . L o c k )

6 H i g h L i m i t 5 2 . 0 oC

M E N U

O K

C a n c e l

Contents

Main CONTENTS 93 2 INTRODUCTION 3 PRECAUTIONS FOR SAFE OPERATION It is imperative that the user complies with this manual as it contains important safety advice. WARNING CAUTION Symbol shows; Be sure to keep this manual in a place accessible to users of this unit. WARNING 95 4 WARNING 97 6 CAUTION LABELS ON THE INCUBATOR EMVIRONMENTAL CONDITIONS INCUBATOR COMPONENTS Page 101 10 Control panel and keypad 3 11 10 It is not possible to silence the buzzer for an upper limit temperature alarm. Remote alarm terminals REMOTE ALARM 103 12 INSTALLATION SITE INSTALLATION 105 14 Connecting a CO2 gas cylinder PREVENTING CONTAMINATION 107 16 PRECAUTIONS FOR CULTURES Using the Unlock Key WARNING CORRECT OPERATION WARNING LCD PANEL 7 5 1 2 3 4 5 6 7 BASIC OPERATIONS ON CONTROL PANEL 111 20 BASIC PARAMETERS Setting the chamber temperature and CO2 density Setting the key lock Removing the key lock 113 22 Setting the key lock password Page 115 24 Setting the upper limit alarm temperature ALARM PARAMETERS 117 26 UV LAMP PARAMETERS Using the UV lamp Precautions when using the UV lamp 119 28 Setting the UV lamp ON period Lighting the UV lamp for 24 hours 121 30 OTHER PARAMETERS Setting the date, time, and log interval Page 123 32 Initial settings (LCD/DAQ parameters) DISPLAYING THE LOG 1 3 4 5 6 125 34 Transferring data WATER LEVEL SENSOR 127 36 ROUTINE MAINTENANCE Cleaning the chamber and Inner attachments Page 129 38 Filling the humidifying pan 131 40 H2O2 DECONTAMINATION Page 133 42 H 2O2 decontamination OKPOKP OKPOKP 135 44 CAUTION Precautions when handling H 2 O decontamination reagent 137 46 ALARMS, SAFETY, AND SELF-DIAGNOSIS UV lamp failure Door alarm Key lock Auto-return Table 3: Alarm and Safety Functions for Automatic Standard Gas Calibration Alarm and safety function Failure during automatic standard gas calibration 139 48 CALIBRATION Temperature/CO2 calibration 1 3 4 5 6 1 3 4 5 6 141 50 TROUBLESHOOTING 143 52 DISPOSING OF THE CO2 INCUBATOR Page 145 54 (Italian) 147 56 AUTOMATIC CO2 CYLINDER CHANGEOVER 3. 149 58 AUTOMATIC CO2 DENSITY CALIBRATION 151 60 Page STACKING INCUBATORS Front SPECIFICATIONS Low humidifying water alarm, PERFORMANCE Safety check sheet