Manuals / Seagate / Computer Equipment / Computer Drive

Seagate ST9600104SS, ST9600204SS, ST9450304SS, ST9450404SS manual Installation, Drive orientation

Models: ST9600104SS ST9450304SS ST9450404SS ST9600204SS

1 82

Download 82 pages 32.11 Kb

Page 53

9.0Installation

Savvio disc drive installation is a plug-and-play process. There are no jumpers, switches, or terminators on the drive.

SAS drives are designed to be used in a host system that provides a SAS-compatible backplane with bays designed to accomodate the drive. In such systems, the host system typically provides a carrier or tray into which you need to mount the drive. Mount the drive to the carrier or tray provided by the host system using four M3 x 0.5 metric screws. When tightening the screws, use a maximum torque of 4.5 in-lb +/- 0.45 in-lb. Do not over-tighten or force the screws. You can mount the drive in any orientation.

Note. SAS drives are designed to be attached to the host system without I/O or power cables. If you intend to use the drive in a non-backplane host system, connecting the drive using high-quality cables is acceptable as long as the I/O cable length does not exceed 10 meters (32.8 feet).

Slide the carrier or tray into the appropriate bay in your host system using the instructions provided by the host system. This connects the drive directly to your system’s SAS connector. The SAS connector is normally located on a SAS backpanel. See Section 10.4.1 for additional information about these connectors.

Power is supplied through the SAS connector.

The drive is shipped from the factory low-level formatted in 512-byte logical blocks. You need to reformat the drive only if you want to select a different logical block size.

Figure 25. Physical interface

9.1Drive orientation

The drive may be mounted in any orientation. All drive performance characterizations, however, have been done with the drive in horizontal (discs level) and vertical (drive on its side) orientations, which are the two pre- ferred mounting orientations.

Savvio 10K.4 SAS Product Manual, Rev. A

45

Image 53

Seagate ST9600104SS, ST9600204SS, ST9450304SS, ST9450404SS manual Installation, Drive orientation

Contents

Standard Models Self-Encrypting Drive Models ST9600204SSST9600104SS ST9450404SSST9450304SSRev. a 12/15/09 Initial release Revision historyContents Installation Defect and error managementAbout self-encrypting drives Interface requirementsSeagate Technology support services Savvio 10K.4 SAS Product Manual, Rev. a List of Figures Page Scope Standards Applicable standards and reference documentationElectromagnetic compatibility Electromagnetic susceptibilityElectromagnetic compliance for the European Union Electromagnetic complianceAustralian C-Tick Korean KCCEuropean Union Restriction of Hazardous Substances RoHS Reference documentsGeneral description Media description Standard featuresReliability PerformanceFormatted capacities Programmable drive capacityFactory-installed options Internal drive characteristics Performance characteristicsSeek performance characteristics Access timeStart/stop time General performance characteristicsCaching write data Prefetch/multi-segmented cache controlCache operation Prefetch operation Error rates Reliability specificationsRecoverable Errors Unrecoverable ErrorsSeek errors Reliability and serviceInterface errors Preventive maintenance4 S.M.A.R.T Maximum processing delay Fully-enabled delayControlling S.M.A.R.T Performance impactThermal monitor Temperature Log Page 0Dh Parameter Code DescriptionPredictive failures Drive Self Test DST State of the drive prior to testingDST failure definition ImplementationShort test Function Code 001b Short and extended testsExtended test Function Code 010b Log page entriesProduct repair and return information Product warrantyShipping PowerChoice modes Physical/electrical specificationsPowerChoiceTM power management DC power requirements AC power requirementsSavvio 10K.4 SAS Product Manual, Rev. a Page Page Conducted noise immunity General DC power requirement notesPower sequencing Current profiles for 600GB models Current profilesCurrent profiles for 450GB models GB models in 3Gb operation Power dissipation600GB models in 6Gb operation 450GB models in 3Gb operation 450GB models in 6Gb operation Temperature a. OperatingEnvironmental limits Shock and vibration Relative humidityEffective altitude sea level a. Operating Shock Recommended mounting Corrosive environment Air cleanlinessVibration a. Operating-normal Acoustics Mounting configuration dimensions Mechanical specificationsAdmin SP Controlled accessAbout self-encrypting drives Data encryptionRandom number generator RNG Default passwordDrive locking Data bandsPower requirements Authenticated firmware downloadSupported commands Cryptographic eraseDrive error recovery procedures Defect and error managementDrive internal defects/errors SAS system errors Deferred Auto-Reallocation Background Media ScanMedia Pre-Scan Idle Read After Write Drive orientation InstallationAir flow CoolingGrounding Drive mountingInterface requirements SAS featuresDual port support Supported commands Scsi commands supportedSupported commands Supported commands Supported commands Savvio inquiry data Mode Sense dataInquiry data Page Mode Pages Mode Sense data for ST9600204SS and ST9600104SS drivesMode Sense values for ST9450404SS and ST9450304SS drives Miscellaneous status Miscellaneous operating features and conditionsMiscellaneous features SAS physical interface Datum B Section C C Section a a Connector requirements Physical characteristicsElectrical description Pin descriptionsPower Signal characteristicsSAS transmitters and receivers Ready LED OutLED drive signal SAS-2 Specification complianceDifferential signals General interface characteristicsInternet Seagate Technology support servicesPresales Support Technical SupportData Recovery Services Call Center Toll-free Direct dialFAX Warranty ServiceData Recovery Services Authorized Service Centers Numerics IndexKCC Msid Mtbf See also cooling Page Savvio 10K.4 SAS Product Manual, Rev. a Page Seagate Technology LLC