| Attaching |
| Elevating | Handwheel | 23 | |||||||
| Installing |
| the Yoke Assembly | 24 | ||||||||
| Removing | the | Blade |
| 25 | |||||||
| Attaching |
| Table |
| Supports | 25 | ||||||
| Setting the Arm Lock Knob | ............................................................................................................................... | 26 | |||||||||
| Setting | the Yoke | Clamp | 26 | ||||||||
| Setting the Bevel Lock Lever | 27 | ||||||||||
| Tightening | the Arm and Column | 28 | |||||||||
| Adjusting |
| the Column | Tube | ........................................................................................................................ | |||||||
| Adjusting |
| the Carriage | Bearings | 30 | |||||||
| Leveling | the Table | Supports | 31 | ||||||||
| Installing |
| the | Front | Table | 32 | ||||||
| Leveling | the | Front Table | 33 | ||||||||
| Installing Rear Table, Spacer Table, Fence, and Clamps | |||||||||||
| Installing |
| Blade | and Blade | Guard | 34 | ||||||
| Aligning |
| Riving | Knife to Blade | 35 | |||||||
| Installing |
| Rip |
| Scale | Indicators | 36 | |||||
• | Adjustments | ................................................................................................................................................ |
|
|
|
|
| |||||
| Aligning |
| the Arm | for Cross | Cuts | 37 | ||||||
| Aligning |
| the Blade | to Table | at 0° Bevel | 38 | ||||||
| Squaring |
| Blade to Fence | 39 | ||||||||
| Paralleling | Blade to Table | 40 | |||||||||
| Aligning |
| the Rip Scale Indicators | 41 | ||||||||
| Installing |
| Control | Cut | Device | 42 | ||||||
| Check | Alignment | of Arm and Blade using Laser | 43 | ||||||||
• | Operation | .................................................................................................................................................... |
|
|
|
|
|
| ||||
| Basic Operation |
| of the Radial Arm Saw | 44 | ||||||||
| Types of Cuts | .................................................................................................................................................... |
|
|
|
| 44 | |||||
| Switch | and Switch | Key | 45 | ||||||||
| Causes | of Kickback |
| 45 | ||||||||
| Avoiding | Kickback | ............................................................................................................................................. |
| 45 | |||||||
| Cutting | Aids |
|
|
|
|
|
| 46 | |||
| Making a Cross |
| Cut |
| 47 | |||||||
| Making a Miter Cut | ............................................................................................................................................ |
| 48 | ||||||||
| Making a Bevel |
| Cut |
| 49 | |||||||
| Making a Compound | Cross Cut | 50 | |||||||||
| Rip Cut Hazards | and Precautions | 51 | |||||||||
| Setting | Up a Rip Cut |
| |||||||||
| Making a Rip Cut |
|
| 52 | ||||||||
| Making | Other |
| Cuts | ............................................................................................................................................ |
| 53 | |||||
| Cutting | Long Workpieces | 53 | |||||||||
|
| Cuts | ............................................................................................................................................ |
| 54 | |||||||
• | Laser Guide | ................................................................................................................................................ |
|
|
|
|
| |||||
• | Maintenance |
| ..................................................................................................................................................... |
|
|
|
| 57 | ||||
• | Troubleshooting |
| .......................................................................................................................................... |
|
| |||||||
• | Exploded |
| View and | Repair | Parts List | |||||||
• | Parts Ordering |
| / | Service | back page | |||||||
3rRI:IFI"$1_tI:INRADIALSAW315.220100
