2Dip Switch Setting | Seiko TM-U590/U590P manual

Transmission Speed

Transmission Speed (BPS)-bits per second	1-7	1-8

2400	ON	ON

4800	OFF	ON

9600	ON	OFF

19200	OFF	OFF

Set 2

	SW	Function	ON	OFF

	2-1	Handshaking (BUSY	Receive buffer full	Off line or
	2-1	condition)	Receive buffer full	receive buffer full
		condition)		receive buffer full

	2-2	Customer display	Connected	Not connected
	2-2	(DM-D) connection	Connected	Not connected
		(DM-D) connection

	2-3~	Undefined	—
	2-4	Undefined	—
	2-4

	2.5~	Internal use	Fixed to Off
	2.6	Internal use
	2.6

	2-7*	I/F pin 6 reset signal	Enabled	Disabled

	2-8*	I/F pin 25 reset signal	Enabled	Disabled

*With a RS-485 serial interface specification (a dealer option), DIP switches 2-7 and 2-8 are ignored.

Notes:

•Changes in DIP switch settings (excluding switches 2-7 and 2-8 interface reset signals) are recognized only when the printer power is turned on or when the printer is reset by using the interface. If the DIP switch setting is changed after the printer power is turned on, the change does not take effect until the printer is turned on again or is reset.

•If you turn on DIP switch 2-7 or 2-8 while the printer is turned on, the printer may be reset, depending on the signal state. DIP switches should not be changed while the printer power is on.

A-2Dip Switch Setting

Image 50

Seiko TM-U590/U590P manual 2Dip Switch Setting

Contents

TM-U590/U590P Printer Parts and Labels Labels Quick Reference Setting Up the PrinterSolving Problems Validating and Verifying ChecksPage Iii FCC Compliance StatementFor American Users Declaration of Conformity EMI and Safety Standards Applied Reference Setting Up and UsingAbout This Manual Introduction FeaturesAccessory Options Ordering Ribbon Cassettes Contents Appendix B Epson Sales Subsidiaries Setting Up the Printer Unpacking 2Setting Up the Printer Removing the protective material Connecting the Cables and Grounding the Printer Connecting the computer 4Setting Up the Printer Connecting the Drawer 6Setting Up the Printer Anschließen der Lade Connecting the Display Module Grounding the Printer Connecting the Power Supply 8Setting Up the PrinterPage Installing the Ribbon Cassette 10Setting Up the Printer Knob Self Test Using the Power Switch Cover12Setting Up the Printer Running the self test DIP Switch Settings Completed Removing the Paper Guide Slide the paper guide to the left to remove it Operating the Control Panels Using the PrinterUsing the Printer Control Panel Panel lights Indicator lights2Using the Printer Slip Paper Handling Reading Micr characters on personal checks Using the Micr Reader Option4Using the Printer Using the Printer General problems TroubleshootingTroubleshooting Printing problems Printout is faint 2TroubleshootingPrinter sounds like it is printing, but nothing is printed Line of dots is missing in the printout Mica cleaning method Recommended Cleaning the Optional Micr MechanismPaper handling problems Cleaning procedure Adhesive Cleaning Sheet 4Troubleshooting Moistened Cleaning sheet Explanatin of a cleaning sheetCommand code sequence Adhesice cleaning sheet Refer to Figure 6Troubleshooting Hexadecimal Dump Paper Printing SpecificationsReference Information Ribbon Specifications Micr Reader Option Paper feed pitch Paper SpecificationsPaper feed method Paper feed speed 4Reference Information Ambient temperature and copy capabilityPaper Copy capability and paper thickness 6Reference Information Reference Information Electrical Characteristics Reliability Mtbf Mcbf Humidity TemperatureEnvironmental Conditions DIP switch functions Dip Switch SettingSetting the DIP Switches Serial interface specification 2Dip Switch Setting Parallel interface specification Dip Switch Setting A-3 Changing the DIP switch settings 4Dip Switch Setting Epson Sales Subsidiaries Epson Sales Subsidiaries B-1 2EPSON Sales Subsidiaries