OPERATION

7.2 Constant Velocity (CV) Driveline

For mowers equipped with a Constant Velocity (CV) driveline, the maximum turning angle between the tractor and mower must be determined to ensure the joint angle does not over-extend which can cause CV joint damage. Constant Velocity joints enable the driveline to operate smoothly with no vibrations and clattering at angles up to 70°. Angles greater than 80° can result in mechanical damage to the CV joint and mower driveline.

The Constant Velocity joint must be lubricated every 8 hours of operation as specified in the Maintenance Section. Failure to properly lubricate the joint will result in accelerated wear and joint component failure.

CV Driveline Maximum Angle Check Procedure

With the mower attached to the tractor and the driveline disconnected from the tractor PTO stub make a hard left turn until there is approximately a 1" clearance between the left rear tractor tire and mower frame or tongue.

Stop and completely shut down the tractor. Place the tractor in Park and apply the Parking Brake before dismounting.

Check the CV joint at this maximum turning radius by holding the driveline yoke above the PTO shaft and then angle the CV joint to its maximum angle. A minimum difference of 10 degrees between the center line of the yoke and the PTO shaft must be maintained to ensure the joint will not be over angled. If the joint cannot be angled at least 10°, there is a potential problem of over-angling the joint while making sharp turns.

Solutions: To ensure the joint is not damaged, check the following:

Check the drawbar length to ensure that it is at the proper length for the RPM speed of the mower. Move the tractor rear tires wider apart to limit the tractor turning radius.

Position the mower at multiple angles and perform the above procedure. Determine the sharpest turning radius that maintains a safe operating angle and note this position to the operator. OPS-R-0006

Turbo 120 01/11

Operation Section 4-19

© 2011 Alamo Group Inc.

OPERATION

Page 129
Image 129
Servis-Rhino TURBO120 manual Constant Velocity CV Driveline, CV Driveline Maximum Angle Check Procedure

TURBO120 specifications

The Servis-Rhino TURBO120 is a cutting-edge rotary cutter designed for agricultural and landscaping applications, renowned for its durability, efficiency, and advanced features. This robust mower is a top choice for professionals and landowners alike, seeking superior performance in tough terrain.

Equipped with a powerful engine, the TURBO120 boasts a high horsepower rating that allows it to tackle dense grass, heavy brush, and overgrown vegetation with ease. The machine’s cutting width of 120 inches enables it to cover large areas quickly, making it an ideal solution for large properties and commercial landscaping tasks.

One of the standout features of the TURBO120 is its heavy-duty construction. Built with a rugged steel frame, this rotary cutter is designed to withstand the rigors of challenging environments. Its reinforced cutting deck both enhances structural integrity and improves the longevity of the machine, minimizing wear and tear even in demanding conditions.

Technologically, the TURBO120 incorporates a unique blade configuration that optimizes cutting efficiency. The rotary blades are designed for maximum cutting performance, ensuring a clean and even cut every time. The machine also features a slip clutch system that protects the drive components, allowing the cutter to handle difficult materials without damage.

User comfort and safety are paramount in the design of the TURBO120. The intuitive controls are easy to operate, allowing users to adjust settings and manage the mower effortlessly. Safety features, including robust guarding around the cutting blades, ensure that users can operate the machine confidently and securely.

The Servis-Rhino TURBO120 is also versatile, with the ability to be attached to various tractors and equipment. Its compatibility with multiple PTO (Power Take-Off) systems enhances its utility, making it a valuable tool for anyone managing large properties, including farmers, landscapers, and maintenance crews.

In summary, the Servis-Rhino TURBO120 presents an impressive blend of power, efficiency, and user-friendly features. Its heavy-duty construction and advanced technologies make it suitable for a wide range of cutting tasks, while safety and comfort considerations ensure an enjoyable and secure mowing experience. Whether dealing with grass or heavy brush, the TURBO120 delivers top-notch performance that professionals can rely on for all their land management needs.