Maintenance
Cleaning the cabinet
Periodically wipe the cabinet with a soft cloth.
Caution:
Do not use chemicals for cleaning (petrol, paint thinner, etc.). It may damage the cabinet fi nish.
Do not apply oil to the inside of each component. It may cause malfunctions.
Error indicators and warnings
When you fail to perform operations properly, the following messages are displayed on the sound bar.
Display | Meaning |
When there is no input signal. Play back the connected equipment.
Nonstandard signal. Cannot
| be recognized. |
| Signals other than DOLBY |
| |
| DIGITAL, DTS, Linear PCM |
(Display blinks) | cannot be recognized. |
Output power | MPO: |
| 160W (80W + 80W) (10% T.H.D.) |
| RMS: Total 160 watts |
| RMS: |
| 160 W (80 W + 80 W) (10% T.H.D.) |
| RMS: |
| 120 W (60 W + 60 W) (1% T.H.D.) |
Output | HDMI™ output: (audio/video support |
terminal | up to 1080p) x 1 |
Input terminal | 500 mV / 47 kohms |
| Optical digital input (OPTICAL): |
| Square type x 1 |
| HDMI input: (audio/video support up |
| to 1080p) x 2 |
|
|
Type | 2 Way speaker system |
| 5.7 cm woofer |
| 2.5 cm Soft Dome |
Bluetooth | 2.400GHz - 2.480GHz |
Frequency |
|
band |
|
Compatible | A2DP (Advanced Audio Distribution |
Bluetooth | Profi le), AVRCP (Audio/Video |
Profile | Remote Control Profi le) |
| Bluetooth 2.1 +EDR |
Error indicator
(blinks red)
Poor connection of the digital audio input terminal.
Turn off the sound bar and check if the cable is connected properly.
When the protection circuit is activated.
Maximum | 160 W |
input power |
|
|
|
Rated input | 80 W |
power |
|
|
|
Impedance | 4 ohms |
(*1): This power consumption value is obtained when the sound bar is in low power consumption mode.
(*): Should the same message appear even if the speaker is unplugged and plugged in, or is set to the standby mode and on again, contact your local dealer where you purchased the sound bar.
Specifications
As part of our policy of continuous improvement, SHARP reserves the right to make design and specifi cation changes for product improvement without prior notice. The performance specifi cation fi gures indicated are nominal values of production unit. There maybe some deviations from these values in individual unit.
Sound Bar
Power source | AC 220 - 240 V ~ 50/60 Hz |
Power | Power on: 38 W |
consumption | Power standby: 0.4 W (*1) |
| Power standby: < 6 W (*2) |
|
|
Dimension | Width: 1386 mm |
| Height: 74 mm |
| Depth: 68 mm |
|
|
Weight | 3.7 kg |
|
|
(*2): This power consumption value is obtained in the STANDBY mode.
Subwoofer
Power source | AC 220 - 240 V ~ 50/60 Hz |
|
|
Power | Power on: 33 W |
consumption | Power standby: 0.4 W (*1) |
| Power standby: 0.4 W (*2) |
Output power | MPO: 150W (10% T.H.D.) |
| RMS: 150 W (10% T.H.D.) |
| RMS: 120 W (1% T.H.D.) |
Type | Subwoofer system |
| 16 cm woofer |
Maximum | 300 W |
input power |
|
Rated input | 150 W |
power |
|
Impedance | 3 ohms |
|
|
Dimensions | Width: 144 mm |
| Height: 432 mm |
| Depth: 306 mm |
Weight | 6.1 kg |
|
|