4
This appliance must be grounded. This oven is equipped with a cord having a grounding wire with a grounding plug.
It must be plugged into a wall receptacle that is properly installed and grounded in accordance with the National
Electrical Code and local codes and ordinances. In the event of an electrical short circuit, grounding reduces risk of
electric shock by providing an escape wire for the electric current.
WARNING – Improper use of the grounding plug can result in a risk of electric shock.
Electrical Requirements
The electrical requirements are a 120 volt 60 Hz, AC only, 15 amp. or more protected
electrical supply. It is recommended that a separate circuit serving only this
appliance be provided.
The oven is equipped with a 3-prong grounding plug. It must be plugged into a wall
receptacle that is properly installed and grounded. Should you only have a 2-prong
outlet, have a qualified electrician install a correct wall receptacle.
A 3-prong adapter may be purchased and used temporarily if local codes allow.
Follow package directions.
A short power-supply cord is provided to reduce risk of becoming entangled in or
tripping over a longer cord.
Extension Cord
If it is necessary to use an extension cord, use only a 3-wire extension cord that has
a 3-blade grounding plug and a 3-slot receptacle that will accept the plug on the
microwave oven. The marked rating of the extension cord should be AC 115-120
volt, 15 amp. or more.
Be careful not to drape the cord over the countertop or table where it can be pulled
on by children or tripped over accidentally.
Notes:
1.If you have any questions about the grounding or electrical instructions, consult a
qualified electrician or service person.
2.Neither Sharp nor the dealer can accept any liability for damage to the oven or personal injury resulting from failure
to observe the correct electrical connection procedures.
Radio or TV Interference
Should there be any interference caused by the microwave oven to your radio or TV, check that the microwave oven
is on a different electrical circuit, relocate the radio or TV as far away from the oven as feasible or check position and
signal of receiving antenna.
UNPACKING AND INSTALLATION INSTRUCTIONSGROUNDING INSTRUCTIONSUnpacking and Examining Your Oven
Carefully remove:
1. all packing materials from inside the oven cavity;
however, DO NOT REMOVE THE WAVEGUIDE
COVER, which is located on
the right cavity wall. Be sure
to remove the turntable
support and place it in the
oven. Read enclosures
and SAVE the Operation
Manual.
2. the feature sticker, if there
is one, from the outside of
the door.
Check the oven for any
damage, such as misaligned or bent door, damaged
door seals and sealing surfaces, broken or loose door
hinges and latches and dents inside the cavity or on
the door. If there is any damage, do not operate
the oven and contact your dealer or SHARP AUTHO-
RIZED SERVICER.
Choosing a Location for Your Oven
You will use the oven frequently so plan its location for
ease of use. It's wise, if possible, to have counter space
on at least one side of the oven. Allow at least 2 inches
on the sides, top and at the rear of the oven for air
circulation. Do not place or install the oven in any area
where heat and steam are generated; for example,
next to or above a conventional gas or electric range
or above a conventional wall oven. Heat and steam
may damage the electronics or the mechanical parts of
the oven.
Built-in Kit
Your oven can be built into a cabinet or wall—not
near or above a heat source—using Sharp’s stainless
steel Built-in Kit RK-42S24 or the black RK-42. If your
dealer does not stock the kit, it can be ordered directly
from the Sharp Accessories and Supplies Center.
Have your credit card number available and call toll-
free: 1-800-642-2122 for ordering the kit to be sent to
your address.
The kit includes duct and simulated frame and easy-to-
follow instructions for installation as well as the location
of the power supply.