Maintenance Indicators
| Maintenance indicator | Problem | Cause | Possible solution | ||||
|
|
|
| |||||
|
| Normal | Abnormal | |||||
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| • Relocate the projector to an area | ||
|
|
|
|
| • Blocked air intake | with proper ventilation (see page | ||
| Temperature |
|
| The internal |
| 8). |
|
|
|
| Red on |
| • Take the projector to your nearest | ||||
| warning | Off | temperature is | • Cooling fan break- | ||||
| (Standby) | Sharp Authorized Projector Dealer | ||||||
| indicator |
| abnormally high. | |||||
|
|
| down | or Service Center (see page 68) | ||||
|
|
|
|
| ||||
|
|
|
|
| • Internal circuit failure | for repair. | ||
|
|
|
|
| • Clogged air intake | • Clean the exhaust and intake | ||
|
|
|
|
|
| vents. (See page 56.) | ||
|
|
|
|
|
|
|
|
|
|
|
|
| The lamp does | • The lamp is shut | • Disconnect the power cord from | ||
|
|
|
| the AC outlet, and then connect it | ||||
|
|
|
| not illuminate. | down abnormally. | |||
|
|
|
| again. | ||||
|
|
|
|
|
| |||
|
|
|
|
|
|
|
| |
|
| Green on | Red on |
|
| • Carefully replace the lamp. (See | ||
|
|
| Time to change | • Remaining lamp life | page 62.) | |||
| Lamp | Green blinks |
| |||||
|
| the lamp. | becomes 5% or less. | • Take the projector to your nearest | ||||
| indicator | when the lamp |
| |||||
|
|
|
| Sharp Authorized Projector Dealer | ||||
|
| is warming up |
|
|
| |||
|
|
|
|
| or Service Center (see page 68) | |||
|
|
|
|
| ||||
|
|
|
|
|
| |||
|
|
| Red on | The lamp does | • | for repair. | ||
|
|
| • Please exercise care when | |||||
|
|
| (Standby) | not illuminate. | • Lamp circuit failure | replacing the lamp. | ||
|
|
|
|
|
| • Securely install the lamp unit cover. | ||
|
|
|
|
|
|
|
| |
|
|
|
|
| • The filter cover, lamp | • If the power indicator blinks even | ||
|
| Green on/ |
| The power | unit cover or lens | when the covers are securely | ||
|
|
| installed, or if the cooling fan does | |||||
| Power | Red on | Red blinks | indicator blinks | housing cover is | |||
| not run normally, then contact your | |||||||
| indicator | Green blinks | in red when the | open. | ||||
|
| nearest Sharp Authorized | ||||||
|
|
| projector is on. | • Cooling fan break- | ||||
|
| (Cooling) |
| Projector Dealer or Service Center | ||||
|
|
|
| down | ||||
|
|
|
|
| (see page 68) for advice. | |||
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
Info
•If the temperature warning indicator illuminates and the projector enters the standby mode, check whether any of the ventilation holes are blocked (see page 8) and then try turning the power back on. Wait until the projector has cooled down completely before plugging in the power cord and turning the power back on. (At least 10 minutes.)
•If the power is turned off for a brief moment due to power outage or some other cause while using the projector, and the power supply recovers immediately after that, the lamp indicator will illuminate in red and the lamp may not be lit. In this case, unplug the power cord from the AC outlet, replace the power cord in the AC outlet and then turn the power on again.
•The cooling fan keeps the internal temperature of the projector constant and this function is controlled automatically. The sound of the cooling fan may change during operation because the fan speed may change and this is not a malfunction.