Manuals / Sharp / Computer Equipment / Projector

Sharp XG-C435X-L Resetting the Lamp Timer, Insert the new lamp unit, Replace the lamp unit cover

Models: XG-C435X-L XG-C465X-L

1 73

Download 73 pages 46.92 Kb

Page 65

5Insert the new lamp unit.

5Insert the new lamp unit.

•Press the lamp unit firmly into the lamp unit compartment. Fasten the securing screws.

6Replace the lamp unit cover.

•Align the lamp unit cover and slide it to close. Then tighten the user service screw to secure the lamp unit cover.

Info

•If the lamp unit and lamp unit cover are not correctly installed, the power will not turn on, even if the power cord is connected to the projector.

User service screw (for lamp unit cover)

Resetting the Lamp Timer

Reset the lamp timer after replacing the lamp.

Info

•Make sure to reset the lamp timer only when replacing the lamp. If you reset the lamp timer and continue to use the same lamp, this may cause the lamp to become damaged or explode.

•You can also reset the lamp timer via the LAN.

(Refer to the SETUP MANUAL on the sup- plied CD-ROM for details.)

1Connect the power cord.

•Plug the power cord into the AC socket of the projector.

2Reset the lamp timer.

•While simultaneously holding down ", ENTER and MENU on the projector, press STANDBY/ON on the projector and keep all four buttons pressed down until the lamp indicator starts blinking green.

•“LAMP 0000H” is displayed, indicating that the lamp timer is reset.

AC socket

Lamp indicator

STANDBY/ON button

ENTER button

"button

MENU button

Appendix

-63

Image 65

Sharp XG-C435X-L Resetting the Lamp Timer, Insert the new lamp unit, Replace the lamp unit cover, Connect the power cord

Contents

Useful Features Appendix Introduction Quick Start Setup Connections Basic OperationMODEL XG-C465X-L XG-C435X-LDANGER Model No Serial NoSPECIAL NOTE FOR USERS IN THE U.K 2. CONSUMER PRODUCT SAFETY ACT 1. WARRANTYENGLISH IntroductionPRODUCT DISPOSAL Caution Concerning Lamp ReplacementMaintenance How to Read this Operation ManualTroubleshooting For Future ReferenceSetup ContentsUsing Useful FeaturesReference SETUP MANUALAppendix IntroductionInfo How to Access the PDF Operation ManualsAccessing the PDF Manuals Introduction IMPORTANT SAFEGUARDSCaution concerning the setup of the pro- jector IMPORTANT SAFEGUARDSCaution concerning the lamp unit The projector may be safely tilted to a maximum angle of 9 degreesTemperature monitor function Using the projector in other countriesCaution regarding usage of the projector Other connected equipmentOptional accessories AccessoriesSupplied accessories Throw Distance The graph below is for 100 inches 254 cm screen with 43 normal modeOptional lenses The standard zoom lens is attached to the projectorProjector Part Names and FunctionsTop View Front View14 WIRED REMOTE terminal Terminal for Computer RGB and Component signalsOutput terminal for Computer RGB and Component signals 15 Remote control sensorPart Names and Functions Remote ControlUsing the Remote Control with a Signal Cable Usable Range Using the Remote ControlInserting the Batteries 2 Insert the batteriesQuick Start Setup and Projection1. Place the projector facing a screen 3. Remove the lens cap and turn the projector on5. Adjust the focus and the zoom 4. Adjust the angle6. Select the INPUT mode 7. Turn the Power offSetting Up the Projector Setting Up the ProjectorStandard Setup Front Projection Example of standard setupSetup Projection PRJ ModeIndication of the Projection Image Size and Projection Distance Picture Size 500F1.7-F1.9, f=28.0-33.6 mm Setting Up the ProjectorStandard Zoom Lens Connections Samples of Cables for ConnectionSamples of Cables for Connection Connections Connecting to a ComputerWhen connecting with the RGB cable When connecting with a DVI digital cable Connecting to a ComputerComputer To AUDIO input terminalWhen connecting video equipment with a DVI output terminal Connecting to Video EquipmentWhen connecting video equipment with component video output terminal ConnectionsWhen connecting video equipment with video output terminal Connecting to Video EquipmentWhen connecting video equipment with S-video output terminal accessory Controlling the Projector by a ComputerConnections InfoControlling the Projector by a Computer Connecting to a Monitor with RGB Input TerminalWhen connecting to the LAN terminal using a LAN cable Connections Connecting to an Amplifier or Other Audio EquipmentAmplifier To AUDIO output terminal MONITOR OUT To audio input terminalTurning the Power Off Put Connecting the Power CordTurning the Projector On/Off Turning the Projector On1 Press the Height Adjustment but- tons Using the Adjustment FeetImage Projection Basic OperationHorizontal Keystone Correction Adjustment with \ Vertical Keystone Correction Adjustment withCorrecting Trapezoidal Distortion Image Projection1 The focus is adjusted by rotat- ing the focus ring Adjusting the Lens2 Zooming is adjusted by moving the zoom knob Focus ringAdjusting the Volume Switching the Input ModeVOL +/- Volume buttons AV MUTE button COMPUTER COMPUTER DVI, S-VIDEO Displaying the Black Screen and Turning off the Sound TemporarilySwitching the Eco+Quiet Mode Displaying and Setting the Break TimerAuto Sync Auto Sync Adjustment 1 Press BREAK TIMER1 Press MAGNIFY on the remote control Selecting the Picture ModePress RETURN on the remote con- trol to cancel the operation MOUSE/Adjustment buttons //\ MAGNIFY buttons RETURN buttonPress RESIZE Resize ModeRESIZE button COMPUTERImage Projection About CopyrightsVIDEO/DTV When moving the cursor Using the Remote Control as the Wireless Computer MouseWhen left-clicking When right-clickingÒPictureÓ menu Menu ItemsThe following shows the items that can be set in the projector ÒScreen adjustment SCR-ADJÓ menu ÒSignal adjustment SIG-ADJÓ menu“Network” menu “Projector adjustment PRJ-ADJ” menuMenu Items Menu Selections Adjustments Using the Menu Screen2 Press or \ and select ÒPic- tureÓ to adjust Useful FeaturesUsing the Menu Screen To adjust the pro- jected image while watching it3 Press or and select ÒBrightÓ to adjust 4 Press \ or to adjust the item selected1 Selecting the Picture Mode Picture Adjustment ÒPictureÓ menu2Adjusting the Image 3 Adjusting the Color Temperature8Eco+Quiet Mode Setting 5 Selecting the Film Mode4 Selecting the Progressive Mode Picture Adjustment ÒPictureÓ menu3 Auto Sync Adjustment Signal Adjustment ÒSIG-ADJÓ Menu4 Signal Type Setting 2 Resolution Setting6 Setting the Video System 7 Checking the Input SignalSignal Adjustment ÒSIG-ADJÓ Menu 5 Selecting the Dynamic Range1 Setting the Resize Mode Screen Adjustment ÒSCR-ADJÓ Menu2 Adjusting the Image Position 3Keystone CorrectionScreen Adjustment ÒSCR-ADJÓ Menu 4 Setting the On-screen Display7Reversing/Inverting Pro- jected Images 8Selecting the On-screen Display Language4Speaker Setting 1 Auto Power Off Function5 Audio Output Type Setting 3 Setting the Confirmation Sound System SoundHelpful Functions Set during Installation ÒPRJ-ADJÓ menu 9Fan Mode SettingSetting/Changing the keycode 8Selecting the Transmis- sion Speed RS-232CTo cancel the keycode that you have al- ready set q Returning to the Default SettingsKeylock Function w Checking the Lamp Life StatusIf you forget the password 1 Setting a PasswordSetting a Password Changing the Password3 TCP/IP Setting 2 DHCP Client Setting3 Enter ÒIP AddressÓ using , , and \, then press ENTER 4 Enter ÒSubnet MaskÓ using , , and \, then press ENTERCleaning the projector MaintenanceCleaning the lens Cleaning the exhaust and intake ventsReplacing the Air Filter 2 Disconnect the power cordReplacing the Air Filter 3 Remove the filter cover6 Replace the filter cover 5 Place a replacement air filterReplacing the Air Filter About the temperature warning indicator Maintenance IndicatorsAbout the lamp indicator AppendixAbnormal Maintenance IndicatorsInfo Lamp Regarding the LampCaution Concerning the Lamp Replacing the LampUser service screw for lamp unit cover Securing screws Removing and Installing the Lamp UnitRegarding the Lamp 3 Remove the lamp unit cover1 Connect the power cord Resetting the Lamp Timer2 Reset the lamp timer AC socket Lamp indicator STANDBY/ON button ENTER button buttonLens cap Fixing band Supplied accessories Remote control, etc Appendix Computer Compatibility ChartComputer 23-29 Troubleshooting23-29 23-29 AppendixFor SHARP Assistance Output terminals SpecificationsAppendix Index SHARP CORPORATION