System Connections
When making system connections, please be certain the AC cord is not plugged into an AC outlet.
When making connections between components, please be sure to connect the white RCA plugs to the L (left) and the red RCA plugs to the R (right) jacks respectively.
Change the position of the FM indoor antenna until you get the best possible reception of your favorite FM stations.
A 75 Ohm outdoor FM antenna may be used to further improve the reception. Disconnect the indoor antenna before connecting the outdoor antenna.
Place the AM loop antenna as far as possible from the receiver, TV set, speaker cords and the AC input cord and set it to a direction for the best reception.
If the reception is poor with the AM loop antenna, an AM outdoor antenna can be used in place of the AM loop antenna.
Make all connections firmly and correctly. Failure to do so can cause loss of sound, noise or damage to the receiver.
If the electricity fails or the AC cord is left unplugged for about two weeks, all operating parameters in the unit’s memory will be lost. Should this happen, you must enter them again.
ENGLISH
■CONNECTING ANTENNAS
FM
(OUTDOOR ANTENNA)
FM
(INDOOR ANTENNA) | AM loop antenna |
300ohm feeder
AM
LOOP
|
| IN | VIDEO | Y |
| DIGITAL | GND | OUT |
|
| IN |
|
| |
|
| PHONO | CB FRONT | |
L | R | VIDEO 3 | OUT | SPEAKERS |
| (8Ω) | |||
“ |
| CD |
| CR |
is a trademark
of SRS Labs, |
| VIDEO 4 |
|
| MONITOR |
| R |
Inc.” | REAR |
| AUX |
|
| Y |
|
| COXIAL |
| OUT |
|
|
|
|
| VIDEO 1 | L | R |
|
|
|
|
|
|
| TAPE | 6.1 CH | 6.1 CH | CB | REAR |
|
|
| MON. | SPEAKERS | |||
| VIDEO 2 |
|
|
|
|
| (8Ω) |
AM |
|
|
|
|
|
|
|
LOOP |
|
| VIDEO 1 | VIDEO 1 | VIDEO 1 | CR |
|
| CD |
|
|
| VIDEO 2 |
| R |
|
|
| VIDEO 2 | VIDEO 2 | VIDEO 2 | Y |
|
| TAPE/MD |
|
|
|
|
| REAR |
|
|
|
|
|
|
| CENTER |
|
|
| VIDEO 3 | VIDEO 3 | VIDEO 3 | CB | SPEAKER |
|
|
| (8Ω) | ||||
|
| OPTICAL |
|
|
|
|
|
|
|
| VIDEO 4 | VIDEO 4 | VIDEO 4 | CR |
|
ANTENNA |
|
|
|
|
|
|
|
L | R |
|
|
|
|
| VIDEO 3 |
OUT | L | R | IN | IN |
120V~60Hz | MODEL NO. |
AC INPUT |
|
4A | AUDIO/VIDEO RECEIVER |
| MADE IN KOREA |
| DESIGNED IN USA |
| SER. NO |
L
Manufactured under license from Dolby Laboratories.“Dolby”,“Pro Logic” and the
All rights reserved.
Manufactured under license from Digital Theater Systems, Inc.
US Pat. No. 5,451,942 and other
Systems, Inc. ©1996 Digital Theater Systems, Inc. All rights reserved.
L |
|
|
|
| ||||
AC OUTLETS |
|
| E 8 5 6 4 9 |
|
| |||
|
|
|
|
|
| 29Z3 |
| |
|
|
|
|
|
| LISTED |
| |
|
|
|
|
| AUDIO EQUIPMENT |
| ||
FRONT |
|
|
|
|
|
| C |
|
CENTER |
|
|
|
|
|
|
| |
SPEAKER |
|
|
|
|
| |||
(8Ω) |
|
|
|
|
|
|
| |
| SWITCHED |
|
|
|
| |||
120V~60Hz |
|
|
|
| ||||
TOTAL 100W 1A MAX |
|
|
|
| ||||
FM
75Ω
SUPPLIED ADAPTOR
" is a trademark of SRS Labs, Inc."
COMPONENT
■CONNECTING AUDIO COMPONENTS
Tumtable with MM type cartridge |
|
|
|
| IN |
| GND | |
PHONO 
|
| CD | |
CD player | OUT | AUX | |
|
| ||
L | R |
| |
TAPE | REC | TAPE | |
MON. | MON. | ||
|
OPTICAL OUT | CD |
| TAPE/MD |
| OPTICAL |
| OUT |
PLAY(LINE OUT)
REC(LINE IN) OPTICAL OUT
OPTICAL IN
Additional MD recorder for digital recording
Additional
audio component
Tape deck or
MD recorder
•The AUX jacks may be connected to an additional audio component such as a CD player, a tape deck, etc.
•Connect the TAPE MONITOR IN/OUT jacks to the PLAY(LINE OUT)/REC(LINE IN) jacks of a tape deck or MD recorder.
•The TAPE MONITOR IN/OUT jacks may also be connected to the LINE OUT/IN jacks of an optional graphic equalizer.
•If a digital recorder or other component with OPTICAL DIGITAL IN/OUT jacks is connected to the corresponding jacks of this unit,
you can playback and/or record the high quality sound of CD’s, etc. without analog conversion or degradation. ■Notes:헵
•The phono input of your receiver is not suitable for the direct connection of a turntable with a Moving Coil (MC) cartridge. If you have a MC cartridge, use a separate head amplifier of
•Not all of the commercially available Fiber Optic cables are suitable for use with this receiver. If you have a question as to the suitability of any cable, please check with your dealer or a qualified service organization.
•Remove the protective cap before making any OPTICAL connections.
5
