Manuals / Sherwood / Home Audio / Stereo Receiver

Sherwood R-963 manual Room 2 Remote Controls

Models: R-963

1 54

Download 54 pages 48.87 Kb

Page 4

ENGLISH

CONTENTS
Introduction
UNPACKING AND INSTALLATION	2
READ THIS BEFORE OPERATING YOUR UNIT	3
System Connections	5
Front Panel Controls	10
Universal Remote Controls
DIGI LINK SYSTEM REMOTE CONTROLS	11
OPERATING COMPONENTS WITH REMOTE CONTROL	13
REMOTE CONTROL OPERATION RANGE	13
LOADING BATTERIES	13
ENTERING A SETUP CODE	14
ADDITIONAL INFORMATION ON REMOTE COMMAND CODES	16
ROOM 2 Remote Controls
REMOTE CONTROL OPERATION RANGE	17
LADING BATTERIES	17
Operations
LISTENING TO A PROGRAM SOURCE	18
SURROUND SOUND	21
ENJOYING SURROUND SOUND	24
LISTENING TO RADIO BROADCASTS	28
RECORDING	30
DIGITAL AUDIO RECORDING WITH MD RECORDER	31
OTHER FUNCTIONS	32
ROOM 2 SOURCE PLAYBACK	34
Using the OSD
CURRENT STATUS DISPLAY	35
OSD Menu Settings	35
SETTING THE POWER AMP ASSIGN	37
SETTING THE SPEAKER SETUP	38
SETTING THE FUNCTION SELECT	41
SETTING THE SURROUND SETUP	47
SETTING THE CH LEVEL TRIM	49
SETTING THE ROOM 2 FEED SETUP	50
Troubleshooting Guide	52
Specifications	53

4

Image 4

Sherwood R-963 manual Room 2 Remote Controls

Contents

963 Unpacking and Installation IntroductionRead this Before Operating Your Unit Room 2 Remote Controls System Connections Should this happen, memorize them againAudio IN/ OUT connections Connecting System Control Connecting MULTI-ROOM System KIT Connecting Speakers Front Panel Controls Dynamic Range ButtonDigi Link System Remote Controls Universal Remote ControlsThis remote control unit has 3 operating modes as follows Function Table of the Numbered Buttons Loading Batteries Remove the coverLoad four alkaline batteries AAA size 5V matching the polarityEntering a Setup Code Buttons simultaneously for 3 secondsPower button and then save the code Code is saved and the Pre-PROgramming mode is resumedOperate the component using Corresponding function buttons Repeat the above stepsAdditional Information on Remote Command Codes Functions MainRoom 2 Remote Controls Matching the polarityOperations Before operationWhen CD, Tape MON or Video 1~ Video 5 is selected Adjusting the tone bass and trebleSelect the tone mode as desired Select the digital or the analog input as DesiredPress it again to cancel, then CINEMA-EQ OFF Surround Sound Surround modesUse this mode to enjoy video game sources Hall 1/2Speaker placement Front left and right speakers and center speakerEnjoying Surround Sound Surr Adjusting each channel level Adjusting each channel level with test toneDownmixing into 2 front channels Auto tuning Manual tuningPresetting radio stations Listening to Radio BroadcastsTuning to preset stations Scanning preset stations in sequenceDubbing the sound and image signals RecordingRecording with Tape Monitor Dubbing from video components ontoDigital Audio Recording with MD Recorder Each time this button is pressed, the correspondingInput is selected as follows Connected, Digital is flickering. ThereOperating the sleep timer Adjusting the brightness of the fluorescent displaysOther Functions Compressing the dynamic range Dolby Digital sources onlyCorrecting or clearing a video label Room 2 Source Playback Room 2 sourceOSD Menu Settings Using the OSDCurrent Status Display Select the desired menu using the Cursor UP /DOWN buttons When selecting the Power AMP AssignWhen selecting the Function Select When selecting the Surround SetupSetting the Power AMP Assign Setting the Speaker Setup When selecting the Speaker ConfigWhen selecting the Speaker Distance When selecting the LFE Level Control Corresponding LFE level modeWhen selecting the Input Setup Setting the Function SelectMoved to the corresponding Digital D E O S E L E C T When selecting the Tone Control When selecting the OSD Mode Off To turn off the current status displayWhen selecting the DC Trigger When the DC Trigger mode is set to OnWhen selecting the Listening Mode Setting the Surround Setup When selecting the Source DirectWhen selecting the Cinema EQ Moved to the corresponding modeWhen selecting the Decoding Mode When selecting the surround modeBe adjusted within the range of -15~+15 dB Setting the CH Level TrimEach time these buttons are pressed, the channel level can Setting the ROOM2 Feed Setup When selecting the Volume ModePress the Cursor UP /DOWN Then press the Enter button When selecting the Function Select for RoomButtons to select the Function Select for Room 2 source Troubleshooting Guide Problem Possible Cause RemedySpecifications Amplifier Section963