Manuals / Siemens / Computer Equipment / Network Card

Siemens SPC3 manual Asynchronous Motorola-Mode, Processor-Read-Timing, XCS Xdsack

Models: SPC3

1 68

Page 55

		SPC3	PROFIBUS Interface Center
		SPC3	PROFIBUS Interface Center

T	=	Pulse cycle (48MHz)
TBD	=	To Be Defined
(1	=	Access to the RAM

(2	=	Access to the register/latches

(3	=	For T = 48MHz

Asynchronous Motorola-Mode, Processor-Read-Timing

AB(10..0)	VALID
	60	61	62
	60	61
DB(7..0)			Data Out
			65
	63		64
AS	63		66
AS
R_W			67
R_W
77	68
XCS			69
XCS
XDSACK		70	72
(normal)		71
		71
XDSACK
(early)
			73
			E_Clock = log.'0'

Asynchronous Motorola-Mode, Processor-Write-Timing

AB(10..0)

DB(7..0)

R_W

XCS

XDSACK (normal)

XDSACK (early)

VALID
60	62
Data In
74	75
76
66
63	67
63
68
	69	78
70	72
71		79
71
73
		E_Clock = log.'0'

SPC3 Hardware Description	V1.3	Page 53
Copyright (C) Siemens AG 2003 All rights reserved.		2003/04

Page 55

Image 55

Siemens SPC3 manual Asynchronous Motorola-Mode, Processor-Read-Timing, XCS Xdsack

Contents

Simatic NET Page SIM Atic NET SPC3 Hardware Description Profibus Interface CenterRelease Date Changes VersionsDirectory Mode RegisterStatus Register Interrupt Controller Watchdog Timer DPBuffer Structure Description of the DP ServicesAsic Test 11.3 Diagnostics Processing from the System ViewPin Assignment Example for the RS 485 Interface SPC3 Introduction Function Overview Cmos Pin DescriptionCPD Cmos with pull down TTLt Schmitt trigger V1.3 Memory Area Distribution in the SPC3 Memory Allocation5FFH Segment Processor Parameters Latches/Register OCH 0DH Significance Write Access0EH 0FH Organizational Parameters RAM 1DH 1AH1BH 1CHAsic Interface Mode RegisterDisstartcontrol EOI Mode Register 1 Mode-REG1, writableSTARTSPC3 Exiting the Offline stateStatus Register Status Register Bit15 . .readable FdlindstSPC3 IRR IMR Interrupt ControllerDxout IAR IMRResponse Time Monitoring Watchdog TimerAutomatic Baud Rate Identification Baud Rate MonitoringDPBuffer Structure PROFIBUS-DP InterfaceUart Aux-Buffer Management RAMSetSlaveAddress SAP55 Description of the DP ServicesSequence for the SetSlaveAddress Utility Parameter Data Structure SetParam SAP61Parameter Data Processing Sequence SPC3 CheckConfig SAP62SlaveDiagnosis SAP60 Diagnostics Processing SequenceSPC3 WriteReadData / DataExchange DefaultSAP Structure of the Diagnostics BufferWriting Outputs Reading Inputs Profibus Interface CenterGlobalControl SAP58 UserWatchdogTimerReadInputs SAP56 GetConfig SAP59ReadOutputs SAP57 Bus Interface Unit BIU Hardware InterfaceUniversal Processor Bus Interface General DescriptionBus Interface V1.3 XINT/MO ModeLow Cost System with 80C32 Switching Diagram PrinciplesSystem X86-Mode Application with the 80 C SPC3Application with th 80 C Uart Interface SignalsAsic Test DC-Specifikation of the I/O- Drivers Technical DataMaximum Limit Values Permitted Operating ValuesTabel 8.3 DC-Specifikation of the I/O- Drivers AC-Specification for the Output DriversCurrent Tabelle 8.5 Leakage current of the output drivers Clock Pulse Timing Timing CharacteristicsSYS Bus Interface Clock pulse 48 MhzTBD ResetTiming in the Synchronous C32-Mode ST-Vers Min Max UnitSynchronous Intel-Mode, Processor-Write-Timing Synchronous Intel-Mode, Processor-Read-TimingST-Vers Timing in the Asynchronous Intel Mode X86 ModeParameter Min Max XWR XCS Asynchronous Intel-Mode, Processor-Read-TimingXRD XCS Xready Asynchronous Intel-Mode, Processor-Write-TimingSynchronous Motorola-Mode, Processor-Read-Timing 4.1 74.2Timing in the Asynchronous Motorola-Mode for example, 68HC16 Synchronous Motorola-Mode, Processor-Write-TimingXCS Xdsack Asynchronous Motorola-Mode, Processor-Read-TimingAsynchronous Motorola-Mode, Processor-Write-Timing Pulse 48 MHz Serial Bus InterfaceHousing PQFP-44 Housing SPC3 Hardware Description 14.15 Symbol Min Typ Max AMI-Vers13.65 13.90TXD Profibus InterfacePin Assignment RTSSN65ALS1176 Example for the RS 485 InterfaceTechnical contact person at ComDeC in Germany AppendixAddresses Profibus User Organisation10.3.2 SPC3 ST General Definition of TermsOrdering of ASICs 10.3.1 SPC3 AMIStatdiag Appendix a Diagnostics Processing in Profibus DPDiagnostics Bits and Expanded Diagnostics IntroductionIdentifier Byte 7 has Etc Identifier Byte 0 has Combi Diagnostics Processing from the System ViewSingle Diagnostics Simatic S5 / COM ETData format in the Siemens PLC Simatic Appendix B Useful InformationPage Siemens Aktiengesellschaft