Sierra 200 owner manual Configuration Parameters, Timing Configuration

Configuration Parameters

Timing Configuration
Parameter Name	Description	Addr	Default	Type		Set Value		Get Value
			Value
dtmf_qual_delay	length of time dtmf tone must be detected by hardware to	48	1	byte	C106	48	B (0…255) D	C107 48 D
	be recognized
telemetrydelayl	time from key up to start of key up telemetry	49	8	byte	C106	49	B (0…255) D	C107 49 D
xmittimeouts_long	time from key up to dropping carrier	50	40	byte	C106	50	B (0…255) D	C107 50 D
xmittimeouts_short	time from key up to dropping carrier with link delay off	51	0	byte	C106	51	B (0…255) D	C107 51 D
dtmftimeouts	timeout between dtmf entry to abort command entry	52	30	byte	C106	52	B (0…255) D	C107 52 D
busytimeouts	dtmftimout for busy signal on case	53	60	byte	C106	53	B (0…255) D	C107 53 D
id_idleto	time before ID is forced after transmit starts after long	54	30	word	C108	54	B (0…255) D	C109 54 D
	transmit gap (repeater port)
id_politeto	time remaining in absolute timeout when ID will be	56	120	word	C108	56	B (0…255) D	C109 56 D
	triggered if transmit is idle (repeat port)
id_absto	absolute timeout for sending ID (normally 10 minutes)	58	600	word	C108	58	B (0…255) D	C109 58 D
id_lnkidleto	time before ID is forced after transmit starts after long	60	5	word	C108	60	B (0…255) D	C109 60 D
	transmit gap (link port)
cmdteldelays	delay after first command recognized until command	62	15	byte	C106	62	B (0…255) D	C107 62 D
	telemetry starts
	delay after first command recognized until command
serteldelays	telemetry starts, with rs232 command source and	63	1	byte	C106	63	B (0…255) D	C107 63 D
	teltolocal=1. Value is 1 (defined by SERTELDELAYS0) if
	teltolocal=0.
dialtonetimeout	timeout for dial tone after prefix recognized if not	64	10	byte	C106	64	B (0…255) D	C107 64 D
	command is entered
parmtimeout	timeout while waiting for a command parameter to be	65	5	byte	C106	65	B (0…255) D	C107 65 D
	entered
fantimeouts	timeout for fans after transmit stops	66	255	byte	C106	66	B (0…255) D	C107 66 D
rcvqdelays_loc	time local receiver needs to detect COR and/or PL until	67	10	byte	C106	67	B (0…255) D	C107 67 D
	detected active, normal value
rcvunqdelays_loc	local receiver delay to drop receiver active, normal value	68	30	byte	C106	68	B (0…255) D	C107 68 D
rcvqdelays_lnk	link receiver delay to receiver active detect, normal value	69	10	byte	C106	69	B (0…255) D	C107 69 D
rcvunqdelays_lnk	link receiver delay to drop receiver active, normal value	70	1	byte	C106	70	B (0…255) D	C107 70 D
rcvqdelays[]	specific radio values, set by set radio defaults	71	see above	byte	C106	71	B (0…255) D	C107 71 D
rcvunqdelays[]	specific radio values, set by set radio defaults	79	see above	byte	C106	79	B (0…255) D	C107 79 D

Strings

Parameter Name	Description	Addr	Default	Type	Set Value	Get Value
			Value
	allocated size of prefix	5
prefix_string	0 terminated string with prefix (0..9, A..B, # allowed)	87		special
	allocated size of ID string	20
id_string	0 terminated string to be sent as repeater ID	92		special
id_string2	0 terminated string with alternate ID	112		special
	allocated size of location string	20
loc_string	0 terminated string with location	132		special
loc_string2	0 terminated string with alternate location	152		special
idselect	OBSOLETE	172	0	byte	C106 172 B (0…255) D	C107 172 D

103