Manuals / Smeg / Kitchen Appliance / Dishwasher

Smeg ST1146SE manual

Models: ST1146SE

1 48

Download 48 pages 14.49 Kb

Page 42

Image 42

Page 42

Image 42

Contents

GUIDE FOR USING THE DISHWASHER AND THE WASHING PROGRAMS Contents 1. Description of the controls D OPTION SELECTION KEY E OPTION SETTING KEYUser instructions 1.1 The control panelξ The correct amount of detergent has been added to the dispenser SWITCHING ONBefore starting a washing program make sure that PROGRAMMINGAssisted programming Wizard Standard programmingUser instructions Reference standard STARTING THE PROGRAMFOR CERTIFICATION BODIES User instructionsLOAD CROCKERY User instructionsNUMBER PROGRAMCONTENTS OF DISPLAY WHEN PROGRAM IS IN PROGRESS INTERRUPTING A PROGRAMUser instructions END OF PROGRAM CHANGING THE PROGRAMANNULLING A PROGRAM User instructionsShown on the DISPLAY G Start delay h 0, 1, .....12/24 DELAYED STARTDELAYED START depending on model OPTIONS available in all programs except the soak programUSE OF 3/1 PRODUCTS OPTION depending on model HALF-LOAD WASH depending on modelShown on the DISPLAY G Half load Off/Upper/Lower Shown on the DISPLAY G 3/1/Normal detergentTO SAVE ON ENERGY! … AND PROTECT THE ENVIRONMENT TO CUT DOWN ON DETERGENT CONSUMPTION! … AND PROTECT THE ENVIRONMENTUser instructions H2O hardness Enable buzzerCUSTOMISING YOUR APPLIANCE User instructionsREMOVING THE DISHES WATER HARDNESS TABLELanguage User instructionsSafety level on 2. TroubleshootingFAULT - DESCRIPTION Fault waterblock TABLE OF MALFUNCTIONS DETECTED BY THE AUTODIAGNOSIS SYSTEMIf the fault persists, call the authorised Technical Service Centre FAULT - DESCRIPTIONPress. switch k.o User instructionsAND FOR CLEANING DISHWASHERS WARNINGS AND RECOMMENDATIONS, GUIDE FOR THE USE OF BASKETSContents USES OTHER THAN THOSE DESCRIBED ABOVE Safety instructions1. Safety and operating instructions NEVER BE REMOVEDSafety instructions Safety instructions AQUASTOP MODELSAPPLIANCE Installation instructions 2. Installation and hook-upFor free-standing models only DRAIN CONNECTION CONNECTING TO THE WATER SUPPLY2.1 Water supply connection Installation instructionsInstallation instructions 2.2 Electrical connection and precautionsIF THE APPLIANCE IS PROVIDED WITH A PLUGLESS SUPPLY CORD NEVER DISCONNECT THE PLUG BY PULLING ON THE POWER SUPPLY LEADFOR GREAT BRITAIN ONLY WHEN CLEANING AND MAINTAINING THE APPLIANCEFuse replacement Installation instructions3.1 Using the water softening system 3. Operating instructionsUser instructions 3.2 Using the rinse aid and detergent dispensers User instructionsADJUSTING THE RINSE AID DISPENSER SETTING ADDING THE RINSE AIDUser instructions ADDING THE DETERGENT User instructionsCorrect loading of the dishes helps ensure optimal washing results 3.3 General warnings and recommendations3/1 Products User instructionsDishes and objects in copper, tin, zinc or brass these tend to stain User instructionsEN 50242 cycle test conditions 3.4 Using the basketsEN 50242 STANDARD LOADS FOR CERTIFICATION BODIES Upper basket on the left, there are two saucers underneath the cupsLOADING THE LOWER BASKET User instructionsCUTLERY BASKET User instructionsUPPER BASKET LOADING THE UPPER BASKETUser instructions ADJUSTING THE UPPER BASKET Version BUser instructions User instructions CLEANING THE SPRAY ARMS 4. Cleaning and maintenanceCLEANING THE WATER INTAKE FILTER 4.1 General warnings and recommendationsPROLONGED DISUSE CLEANING THE FILTER UNITGENERAL WARNINGS AND RECOMMENDATIONS FOR CORRECT MAINTENANCE Fill the rinse aid dispenser Shut off the water supply tapBEFORE STARTING THE DISHWASHER AFTER PROLONGED DISUSE TROUBLESHOOTING MINOR PROBLEMSIf the dishes are not being cleaned properly, check that Reconnect the water intake hose and open the tap againIf there are visible traces of rust inside the tank If the dishes fail to dry or remain dull, check thatIf the dishes show signs of streaking, staining, etc., check that User instructionsPage Page Page Page Page