GUIDE FOR USING THE DISHWASHER AND THE WASHING PROGRAMS
Contents
D OPTION SELECTION KEY E OPTION SETTING KEY
User instructions
1. Description of the controls
1.1 The control panel
SWITCHING ON
Before starting a washing program make sure that
ξ The correct amount of detergent has been added to the dispenser
PROGRAMMING
Assisted programming Wizard
Standard programming
User instructions
STARTING THE PROGRAM
FOR CERTIFICATION BODIES
Reference standard
User instructions
User instructions
NUMBER
LOAD CROCKERY
PROGRAM
CONTENTS OF DISPLAY WHEN PROGRAM IS IN PROGRESS
INTERRUPTING A PROGRAM
User instructions
CHANGING THE PROGRAM
ANNULLING A PROGRAM
END OF PROGRAM
User instructions
DELAYED START
DELAYED START depending on model
Shown on the DISPLAY G Start delay h 0, 1, .....12/24
OPTIONS available in all programs except the soak program
HALF-LOAD WASH depending on model
Shown on the DISPLAY G Half load Off/Upper/Lower
USE OF 3/1 PRODUCTS OPTION depending on model
Shown on the DISPLAY G 3/1/Normal detergent
TO SAVE ON ENERGY! … AND PROTECT THE ENVIRONMENT
TO CUT DOWN ON DETERGENT CONSUMPTION! … AND PROTECT THE ENVIRONMENT
User instructions
Enable buzzer
CUSTOMISING YOUR APPLIANCE
H2O hardness
User instructions
WATER HARDNESS TABLE
Language
REMOVING THE DISHES
User instructions
2. Troubleshooting
FAULT - DESCRIPTION Fault waterblock
Safety level on
TABLE OF MALFUNCTIONS DETECTED BY THE AUTODIAGNOSIS SYSTEM
FAULT - DESCRIPTION
Press. switch k.o
If the fault persists, call the authorised Technical Service Centre
User instructions
AND FOR CLEANING DISHWASHERS
WARNINGS AND RECOMMENDATIONS, GUIDE FOR THE USE OF BASKETS
Contents
Safety instructions
1. Safety and operating instructions
USES OTHER THAN THOSE DESCRIBED ABOVE
NEVER BE REMOVED
Safety instructions
Safety instructions
AQUASTOP MODELS
APPLIANCE
Installation instructions
2. Installation and hook-up
For free-standing models only
CONNECTING TO THE WATER SUPPLY
2.1 Water supply connection
DRAIN CONNECTION
Installation instructions
2.2 Electrical connection and precautions
IF THE APPLIANCE IS PROVIDED WITH A PLUGLESS SUPPLY CORD
Installation instructions
NEVER DISCONNECT THE PLUG BY PULLING ON THE POWER SUPPLY LEAD
WHEN CLEANING AND MAINTAINING THE APPLIANCE
Fuse replacement
FOR GREAT BRITAIN ONLY
Installation instructions
3.1 Using the water softening system
3. Operating instructions
User instructions
3.2 Using the rinse aid and detergent dispensers
User instructions
ADJUSTING THE RINSE AID DISPENSER SETTING
ADDING THE RINSE AID
User instructions
ADDING THE DETERGENT
User instructions
3.3 General warnings and recommendations
3/1 Products
Correct loading of the dishes helps ensure optimal washing results
User instructions
Dishes and objects in copper, tin, zinc or brass these tend to stain
User instructions
3.4 Using the baskets
EN 50242 STANDARD LOADS FOR CERTIFICATION BODIES
EN 50242 cycle test conditions
Upper basket on the left, there are two saucers underneath the cups
LOADING THE LOWER BASKET
User instructions
CUTLERY BASKET
User instructions
UPPER BASKET
LOADING THE UPPER BASKET
User instructions
ADJUSTING THE UPPER BASKET
Version B
User instructions
User instructions
4. Cleaning and maintenance
CLEANING THE WATER INTAKE FILTER
CLEANING THE SPRAY ARMS
4.1 General warnings and recommendations
CLEANING THE FILTER UNIT
GENERAL WARNINGS AND RECOMMENDATIONS FOR CORRECT MAINTENANCE
PROLONGED DISUSE
Fill the rinse aid dispenser Shut off the water supply tap
TROUBLESHOOTING MINOR PROBLEMS
If the dishes are not being cleaned properly, check that
BEFORE STARTING THE DISHWASHER AFTER PROLONGED DISUSE
Reconnect the water intake hose and open the tap again
If the dishes fail to dry or remain dull, check that
If the dishes show signs of streaking, staining, etc., check that
If there are visible traces of rust inside the tank
User instructions
Page
Page
Page
Page
Page