Manuals / Snapper / Lawn and Garden / Lawn Mower

Snapper LT160H42FBV2, LT180H48FBV2 Familiarization, Components, Controls

Models: LT160H42FBV LT180H48FBV2 LT160H42FBV2

1 44

Download 44 pages 46.28 Kb

Page 5

Section 1 - FAMILIARIZATION

Section 1 - FAMILIARIZATION

CLUTCH/BRAKE PEDAL

PARK

BRAKE

LEVER

DOWN

OPERATOR’S

SEAT

SPEED

CONTROL

LEVER

BATTERY (UNDER SEAT)

SEAT

ADJUSTMENT

KNOB

CUTTING

HEIGHT

ADJUSTMENT

LEVER

DISCHARGE

DEFLECTOR

MOWING DECK (42” SHOWN)

LIGHT

SWITCH

CHOKE

BLADE

SWITCH

FAST

SLOW

STEERING	ENGINE SPEED	IGNITION
STEERING	CONTROL	KEY
WHEEL

DASHBOARD CONTROLS

FUEL TANK (UNDER HOOD)

HOOD

HEADLIGHTS

ENGINE

FIGURE 1.1

COMPONENTS

The nomenclature drawings above, illustrate the essential components of the SNAPPER Lawn Tractor. It is recommended that all operators of this equipment become thoroughly familiar with the components and their operation BEFORE OPERATING. Specific details involving the engine are found in the separate Engine Owner’s Manual.

Study the Important Safety Instructions, this Operator’s Manual and Engine Owner’s Manual before operating this machine. Keep these manuals available for future reference.

CONTROLS

All operators should be acquainted with the operator’s controls before attempting start-up or operation of the Lawn Tractor. See the Control Panel drawing above.

5

Image 5

Snapper LT160H42FBV2, LT180H48FBV2 important safety instructions Familiarization, Components, Controls

Contents

LAWN TRACTOR HYDROSTATIC DRIVE ELECTRIC CLUTCH SERIES F Safety Instructions & Operator’s Manual forMODELS LT160H42FBV LT160H42FBV2 LT180H48FBV2PROTECTION FOR CHILDREN IMPORTANT SAFETY INSTRUCTIONSPROTECTION AGAINST TIPOVERS PREPARATIONOPERATION MAINTENANCEIMPORTANT SAFETY INSTRUCTIONS PREPARATIONTROUBLESHOOTING GUIDE TABLE OF CONTENTSIMPORTANT SAFETY INSTRUCTIONS CONTROLS Section 1 - FAMILIARIZATIONCOMPONENTS 2.2 OPERATOR’S SEAT ADJUSTMENT 2.2.1. FRONT TO REAR ADJUSTMENT Section 2 - OPERATING INSTRUCTIONS2.1 PRE-START CHECKLIST 2.3 STARTING & OPERATION 2.3.1. STARTING ENGINE Section 2 - OPERATING INSTRUCTIONS2.3 STARTING & OPERATION Continued 2.3.2. STARTING WHEEL DRIVE Section 2 - OPERATING INSTRUCTIONS2.3.3 STARTING MOWER BLADE 2.4 STOPPING ENGINE, BLADE, WHEEL DRIVE 2.4.1 STOPPING ENGINE2.4 STOPPING 2.4.3. STOPPING MOWER BLADES Section 2 - OPERATING INSTRUCTIONS2.6. ROLLING TRACTOR WITH ENGINE OFF Rolling Hydro Models Section 2 - OPERATING INSTRUCTIONS3.2 SERVICE - AFTER FIRST 5 HOURS Section 3 - MAINTENANCE3.1 INTRODUCTION 3.2.1. CHANGE ENGINE OIL3.2.4. CHECK DECK DRIVE BELT Section 3 - MAINTENANCE3.3.4. TRACTOR LUBRICATION Continued From Previous Page Section 3 - MAINTENANCE3. Clutch/Brake Pivot 4. Steering Sector Gear3.4 ANNUALLY END OF EACH SEASON Section 3 - MAINTENANCE3.4.1. ENGINE 3.4.2. FUEL FILTERSection 4 - ADJUSTMENT & REPAIR 2. Move sector plate as required to raise or lower the rear of deck Section 4 - ADJUSTMENT & REPAIRPLACE THREE 2 X 4 UNDER FRONT AND REAR OF DECK Section 4 - ADJUSTMENT & REPAIRFRONT LIFT FRONT LIFT ARMREAR LIFT ROD REMOVE WASHER & HAIR PIN ROTATE SWIVEL UP OR DOWN Section 4 - ADJUSTMENT & REPAIRREMOVE WASHER & HAIR PIN ROTATE SWIVEL UP OR DOWN SWIVEL FRONT LIFT RODDECK BRACKETSWIVELTo be properly adjusted, the brake should stop Section 4 - ADJUSTMENT & REPAIR4.3.3. SHIFTER ADJUSTMENT Continued from page Section 4 - ADJUSTMENT & REPAIRNEW BLADE WEAR LIMIT. CRACKS OR NOTCHES BEGIN TO APPEAR Section 4 - ADJUSTMENT & REPAIRDANGEROUS CONDITION DO NOT USE ON MOWER 22º TO 28º STANDARD BLADEDECK/DRIVE Section 4 - ADJUSTMENT & REPAIR2. Turn engine “OFF”. Remove key 3. Lower the deck to lowest setting Section 4 - ADJUSTMENT & REPAIR10. Make note of hole used in sector plates Section 4 - ADJUSTMENT & REPAIRSection 4 - ADJUSTMENT & REPAIR Traction drive belt replacement Section 4 - ADJUSTMENT & REPAIRVIEW FROM UNDERNEATH TRACTOR 42” DECK SHOWN1. Place tractor on a firm level surface Section 4 - ADJUSTMENT & REPAIRSection 4 - ADJUSTMENT & REPAIR REMOVE POSITIVE + CABLE LAST REMOVE NEGATIVE CABLE FIRST Section 4 - ADJUSTMENT & REPAIRREMOVE ADJUSTING KNOBS AND MOVE SEAT FORWARD 4.5.5. BATTERY TESTING Section 4 - ADJUSTMENT & REPAIR2. Remove spindle pulley from spindle shaft Section 4 - ADJUSTMENT & REPAIRAVAILABLE ACCESSORIES Section 4 - ADJUSTMENT & REPAIRACCESSORIES AVAILABLEMODEL - LT160H42FBV SECTION 5 - ELECTRICAL SYSTEMSECTION 5 - ELECTRICAL SYSTEM MODELS - LT160H42FBV2 & LT180H48FBV2PROBLEM TROUBLESHOOTING GUIDEPROBABLE CAUSE CORRECTIVE ACTIONTROUBLESHOOTING GUIDE MAINTENANCE PARTS MAINTENANCE SCHEDULETRACTOR DRIVE BELTS3 YEAR LIMITED WARRANTY PRIMARY MAINTENANCE PRIMARY MAINTENANCE PRIMARY MAINTENANCE PRIMARY MAINTENANCE SERVICE NOTES LAWN TRACTOR HYDROSTATIC DRIVE ELECTRIC CLUTCH SERIES F Safety Instructions & Operator’s Manual forSnapper products are built using engines that meet or exceed all applicable emissions requirements on the date manufactured. The labels on those engines contain very important emissions information and critical safety warnings. Read, Understand, and Follow all warnings and instructions in this manual, the engine manual, and on the machine, engine and attachments. If you have any questions about your Snapper product, contact your local authorized Snapper dealer or contact Snapper Customer Service at Snapper, McDonough, GA. 30253. Phone